Oil Feed/RX7/1.8's/DSM/Clamps/Header - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


Miata parts for sale/trade Buy, trade or sell your Miata parts here.

Reply
 
 
 
LinkBack Thread Tools Search this Thread
Old 09-03-2007, 12:31 PM   #1
Elite Member
Thread Starter
iTrader: (7)
 
samnavy's Avatar
 
Join Date: Apr 2006
Location: VIRGINIA BEACH, VA
Posts: 6,020
Total Cats: 175
Default Oil Feed/RX7/1.8's/DSM/Clamps/Header

It's time to get serious.

1: -4an 25" teflon/braided oil feed line w/fitting for T25... you still need the fitting for the block. This is long enough to go over the top, underneath, or around the brake lines: $35 shipped

2: RX7 AFM slightly ported on the inlet w/3"-2.5" 4-ply reducing coupler and pigtail: $35 shipped

3: 9xT-bolt clamps: 4x2" 3x2.5" 1x3" 1x3.25": all for $20shipped (pic next post)... SOLD

4: T25 PORTED turbine housing for DSM .48/.49 T25... should see improved spool and way better top-end: $20+shipping.

5: 1.8injectors, used for about 25test miles since being professionaly done by cleaninjectors.com. I'll send you the test sheet which shows 110/110/110/112. I paid $50 for inj's+$55cleaning. You can see that one has part of the plastic injector clip is cracked. It will not affect performance at all: $65 shipped.

I don't **** around. Paypal only. Your stuff will be shipped the day I receive payment if it's early enough, or the day after at the latest. Just ask for a local pickup price.

You can post dibs here for my asking price or PM me if you want to work something out. If you dib something, I will PM you my Paypal and wait one day for payment before taking another offer.
Attached Thumbnails
Oil Feed/RX7/1.8's/DSM/Clamps/Header-dsc03500-small-.jpg   Oil Feed/RX7/1.8's/DSM/Clamps/Header-dsc03498-small-.jpg   Oil Feed/RX7/1.8's/DSM/Clamps/Header-dsc03499-small-.jpg   Oil Feed/RX7/1.8's/DSM/Clamps/Header-dsc03496-small-.jpg   Oil Feed/RX7/1.8's/DSM/Clamps/Header-dsc03492-small-.jpg  


Last edited by samnavy; 09-03-2007 at 12:47 PM.
samnavy is offline   Reply With Quote
Old 09-03-2007, 12:37 PM   #2
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Sam, I'll take the t-clamps. Plz PM w your address.
Ben is offline   Reply With Quote
Old 09-03-2007, 12:43 PM   #3
Elite Member
Thread Starter
iTrader: (7)
 
samnavy's Avatar
 
Join Date: Apr 2006
Location: VIRGINIA BEACH, VA
Posts: 6,020
Total Cats: 175
Default

^Ben, PM'd


Also been trying to offload this on Craigslist for months w/no takers.

Racing Beat 4-1 Header for 1.6liter w/about 50k miles of use. It's stainless and should last forever. I'll throw in a custom heatshield and used cat (that works perfectly) for my asking price. This thing is about $450shipped from Moss. It's a standard upgrade for an NA car.
$275 local pickup. I'll ship at your expense.


Also pic of clamps...SOLD
Attached Thumbnails
Oil Feed/RX7/1.8's/DSM/Clamps/Header-diy-heat-shield.jpg   Oil Feed/RX7/1.8's/DSM/Clamps/Header-rb-4-1.jpg   Oil Feed/RX7/1.8's/DSM/Clamps/Header-dsc03497-small-.jpg  

Last edited by samnavy; 09-04-2007 at 07:05 PM.
samnavy is offline   Reply With Quote
Old 09-03-2007, 12:52 PM   #4
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Thanks Sam

Who did the turbine housing porting? Do it yourself? I want to do that to my TDo4.
Ben is offline   Reply With Quote
Old 09-03-2007, 01:34 PM   #5
Elite Member
Thread Starter
iTrader: (7)
 
samnavy's Avatar
 
Join Date: Apr 2006
Location: VIRGINIA BEACH, VA
Posts: 6,020
Total Cats: 175
Default

I'm also going to throw out this teaser as a reward for checking my ad... In a month or two, I'll be going Megasquirt and will be selling my entire current fuel/spark setup. This consists of:
Bipes
Begi 2025 APFR w/restrictor and extra check valve
Olderguys 02clamp w/sensor
Walbro 190lph HP fuel pump mounted in pump assembly
305cc Supra injectors
Complete dual feed fuel rail setup w/remote gauge and extra fuel rail
eBay Voodoo MBC

This setup at 12psi on any IC'd T25 makes 200whp w/100psi fuel pressure.

I am not taking offers or dibs on any individual part. If you'd like to discuss an offer for everything, then PM me and we can begin a dialogue. Obviously some flexibility will be required and there are no promises with such a long timetable. If the Navy decides my flight bonus gets delayed, all bets are off.

If you're thinking... why would I get this stuff when I can get MS?
Megasquirt is $720 shipped... after you figure EBC/IAT/WB02/Inj's and one or two other things.... you're at $1100 or more. What I have above and a few dyno pulls will have you set you back around half that.

Again, just something to think about.
samnavy is offline   Reply With Quote
Old 09-03-2007, 01:38 PM   #6
Elite Member
Thread Starter
iTrader: (7)
 
samnavy's Avatar
 
Join Date: Apr 2006
Location: VIRGINIA BEACH, VA
Posts: 6,020
Total Cats: 175
Default

Ben, the housing was aquired during my original Frankenturbo build. I actually purchased 4 DSM T25's and this one came ported. I checked out the DSM sites and it's a standard upgrade when the housing starts to crack... you just grind down the crack to fresh metal and never have to worry about it again. I think I remember a port job costs $40.
samnavy is offline   Reply With Quote
Old 09-04-2007, 12:40 PM   #7
Senior Member
 
steelrat's Avatar
 
Join Date: Jul 2005
Posts: 514
Total Cats: 0
Default

Hey Sam....

You might want to specify if the header is a 1.6, or 1.8 -- different....

Also from the pictures it actually looks like the newer RB 4->1 header not a 4-2-1.... the 4-2-1 doesn't have the "hump" on the #4 runner....

Dave,
steelrat is offline   Reply With Quote
Old 09-04-2007, 01:27 PM   #8
Senior Member
iTrader: (1)
 
Join Date: Jun 2006
Location: Outside of the Loop-ATL
Posts: 754
Total Cats: 0
Default

Quote:
Originally Posted by samnavy View Post
Ben, the housing was aquired during my original Frankenturbo build. I actually purchased 4 DSM T25's and this one came ported. I checked out the DSM sites and it's a standard upgrade when the housing starts to crack... you just grind down the crack to fresh metal and never have to worry about it again. I think I remember a port job costs $40.
Hey the port job you have there to convert a 6cm housing to a 7cm housing. It will sac some low end to greatly increase top end.

BTW anyone looking to use that housing will want to get a a 7cm gasket(can be picked up at any DSM shop. Also would be worth porting you manifold turbo opening.)

Just any FYI for anyone... it is a great up grade and I am about to start porting my 14B that I am going to use for my turbo build.
wildfire0310 is offline   Reply With Quote
Old 09-04-2007, 07:04 PM   #9
Elite Member
Thread Starter
iTrader: (7)
 
samnavy's Avatar
 
Join Date: Apr 2006
Location: VIRGINIA BEACH, VA
Posts: 6,020
Total Cats: 175
Default

^Steel, much thanks... original post edited.
^Wild, thanks for your additional data too.
samnavy is offline   Reply With Quote
Old 09-10-2007, 01:16 PM   #10
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

I got all the clamps Sam, thanks much.
Ben is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
OTS Bilstein to motorsports ASN conversion stoves Suspension, Brakes, Drivetrain 5 04-21-2016 04:00 PM
My solution for Oiltemp and Oilpressure input into Megasuirt (MS3) Zaphod MEGAsquirt 41 01-24-2016 01:25 PM
Moroso Air Oil Separator Catch Can Aroundcorner Miata parts for sale/trade 2 10-01-2015 04:20 PM
Low oil pressure after 1.8 swap and new turbo setup JesseTheNoob DIY Turbo Discussion 15 09-30-2015 03:44 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 09:49 PM.