I've got quite a few nice items available. Been stock piling these for 5+ years.

Mazda Comp motor mounts new still in plastic, shipped SOLD

Mazda Comp diff mounts, new still in plastic, $110 shipped NEW Price





Exedy Pressure Plate, Stock replacement clutch new/unused $60 shipped - taking $10 off price due to the disk not being Exedy



South Bend Clutch 10-045-DXD sintered iron, 6 puck disk, increased clamp load PP ~300lb/ft $300 shipped. (new price $250 shipped)






OEM water pump 1.8, new shipped SOLD

OEM timing belt 1.8 new shipped SOLD

OEM 1.8 intake manifold, runners tapped for direct port nitrous nozzles, can be plugged or used for direct port W/I. $60 shipped.



Tubular turbo manifold 1.8 (not PS/AC compatible), T4 flange, ext wastegate $300 + shipping.





Older FM/(BEGI?) Intake manifold 1.8, was black powder coated had stripped and mirror finish polished (cost $300 for polishing). Came drilled for direct port nitrous which pre-bent lines and nozzles can be included for additional cost. SOLD

Polished Throttle body that was intended to work with intake manifold $45 shipped. SOLD

Racing Beat items:

RB Street springs I bought from member here but never used. SOLD

RB intake elbow, no filter or hardware $5 + actual shipping cost Pending




Paypal accepted. Let me know if you have any questions.

Also have a built short block 1.8 (1.9? .030 overbore) with Cat/Eagle rods, Supertech pistons, balanced rotating assembly, I'll get pictures of shortly. Pending local sale, if falls through I'll post pics and shipping. Any ideas on how to ship a block?

Chuck

 

Paypal ready for the Motor Mounts assuming $45 for the pair.......still don't have enough to PM. Nice and close (63385) for shipping.

 

Yes it is for the pair.

You can use blrx7r1@yahoo(dot)com for my Paypal address. Thanks for looking.

Chuck

 

I will PM you on the intake and TB defenitely interested

 

Motor mounts pending sale to jaf1901

 

Money for the mounts is off to you. Thanks.

 

Motor mounts sold!!! Thanks Jon.

 

Hmmm. in kcmo?

Anymore info on this block?
Might be interested.

Also in the clutch, guessing 1.8 on it as well?

 

What's the clutch rated for. I'm doing a 200hp turbo setup on my 1.8 and do you know if the Mazda comp diff mount bushings are the same my rx7 turbo?

 

I am also interested in the short block. More info and pics would be awesome.

 

Short Block:
MAZDA PISTONS 84.MM 8.6:1 WITH RINGS AND PIN - Supertech purchased through Belfab Racing
CAT rods purchased through Belfab racing
Fully assembled and balanced by machine shop.

I'll get pics tomorrow. I'm on the Kansas side but yes KC metro area. Local would be awesome, I have no idea how to ship a block.

Oh the clutch listed is for a 1.8 and it's basically a stock replacement unit.

 

Price on block ?

 

In for block/flywheel price, and maybe clutch sans shipping. ( I am 30 mins away max )

 

Pm'ed would like to pick up fidanza flywheel and OE clutch.

 

That intake manifold is bitchin'. Someone buy that and set those ports up for meth.

GLWS

 

Sounds good I'll text you and set up a time.

 

Thanks man. Yea I'm kinda surprised, I thought the intake would go quickly. It was going to be one of the crown jewels of my build.

Here are pics showing the N20 setup.









I'm thinking it could be switched to direct port meth easily...

 

hi, will t/b fit standard 1.8 manifold?.what bore size? cheers

 

I doubt it will fit a stock 1.8, I have one so I could go check. The throttle body is 70mm. I was digging through some old emails looking for the info and found that I bought the intake mani and T/B from Mark Kulak back in 2006. In case you weren't aware he had one of the highest hp Miata's at the time. I'll see if it fits OEM and let you know.

 

Intake, T/B, nitrous setup pending sale.