Parting 1995 in Minnesota
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2007
Location: St. Paul
Posts: 132
Total Cats: 0
Parting 1995 in Minnesota
I picked up a 1995 Mazda Miata to pull a few parts I needed. I have pulled everything else and have it for sale. The number of parts is too long to list out so I will list what is NOT available. Most other things are likely available, just ask. Car had full options including A/C, P/S, Power windows, power mirrors, headrest speakers. Larger muffler and Grant steering wheel are the only aftermarket parts I can think of. About 130K on the car.
Parts that are unavailable:
Front bumper cover
Front headlights
Springs/shocks
Rear diff, axles/driveshaft
Transmission
Clutch/flywheel
The front fenders are pretty dented. Soft top is pretty trashed (but could be used for a Project-G style bikini top maybe). The soft top frame is fine.
All other parts are in varying condition, some great, some worn. Again, just ask. As for prices, just make me a fair offer. Email, call or text. 65one - 3one9 - one903
I took a video prior to parting so people could see it in operation.
Parts that are unavailable:
Front bumper cover
Front headlights
Springs/shocks
Rear diff, axles/driveshaft
Transmission
Clutch/flywheel
The front fenders are pretty dented. Soft top is pretty trashed (but could be used for a Project-G style bikini top maybe). The soft top frame is fine.
All other parts are in varying condition, some great, some worn. Again, just ask. As for prices, just make me a fair offer. Email, call or text. 65one - 3one9 - one903
I took a video prior to parting so people could see it in operation.
#3
I tried to PM but I don't have enough posts.
I'm down in SW Minnesota by Worthington. What condition is your interior in? Can you send some photos?
I have been considering putting power windows in mine. How much for both regulators, switch and wiring?
My email is heyjim@live.com and phone 507 360 5382
Thanks!
I'm down in SW Minnesota by Worthington. What condition is your interior in? Can you send some photos?
I have been considering putting power windows in mine. How much for both regulators, switch and wiring?
My email is heyjim@live.com and phone 507 360 5382
Thanks!
#5
Junior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2007
Location: St. Paul
Posts: 132
Total Cats: 0
Charchri4, the interior is pretty good, but obviously not brand new given the miles. The only exceptions I can think of are the driver's seat has a 1.5x3" hole in the outer bolster, the center console just left of the shifter had a hole drilled for a switch, and the door cards could use retacking between the upper and lower portions (they are in good condition visually, just need reattachment).
I'm not sure on pricing. I know regulators tend to cost a bit since they like to break. I definitely have those and the switches. I'm not sure about wiring for the windows though. It might be integrated in to a larger harness.....
Slammed200, I tried to return your PM, but your box is full. I will check on the things you asked for this evening.
I will try to get pictures out to both of you this evening.
I'm not sure on pricing. I know regulators tend to cost a bit since they like to break. I definitely have those and the switches. I'm not sure about wiring for the windows though. It might be integrated in to a larger harness.....
Slammed200, I tried to return your PM, but your box is full. I will check on the things you asked for this evening.
I will try to get pictures out to both of you this evening.
#10
Junior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2007
Location: St. Paul
Posts: 132
Total Cats: 0
Is there a chance you have a picture of the part? Everything is in boxes in my garage so little things are harder to identify. I may or may not have kept the bracket. I took a lot of small parts off the car, but not everything.
#13
Junior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2007
Location: St. Paul
Posts: 132
Total Cats: 0
So unfortunately I didn't get a chance to dig through boxes to find the steering wheel or fuse box mount, but I did snap a few photos of the interior bits I was asked for. Note: Everything is dirty and looks worse than it is. The blemishes in the door cards are just dimples from sitting against other parts and should smooth out. The dash shot shows the one crack, about an inch long at the bottom left hand corner of the airbag cover. The cover itself is crap.
#16
Junior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2007
Location: St. Paul
Posts: 132
Total Cats: 0
PM'd on the trunk.
I do not have the shell any more so I can't cut the quarters. I tried for my other car actually and it is a royal pain. It wasn't even worth doing to repair my rusty miata. I suggest buying new from isellmiataparts.com. They are affordable.
I dug out the steering wheel. Unfortunately I noticed the horn button got cracked at some point. The hub seems to be of good quality (heavy metal, heavy rubber). The cracks in the vinyl are visible.
I do not have the shell any more so I can't cut the quarters. I tried for my other car actually and it is a royal pain. It wasn't even worth doing to repair my rusty miata. I suggest buying new from isellmiataparts.com. They are affordable.
I dug out the steering wheel. Unfortunately I noticed the horn button got cracked at some point. The hub seems to be of good quality (heavy metal, heavy rubber). The cracks in the vinyl are visible.
#18
Junior Member
Thread Starter
iTrader: (2)
Join Date: Sep 2007
Location: St. Paul
Posts: 132
Total Cats: 0
I'm working on it. If I have it it is in a huge box full of small parts in the corner of the garage which means pulling a car out and spreading the contents of the box across the garage to sort it all. I'll get to it as soon as I can. Sorry it is taking a while.