Ultrashields, Harness, Harness bar, Torsen, etc
 

FS: Seats & Harnesses (17’’ Ultrashield/ 6pt Gforce); FS/WTT: 4.1 & 4.3 Torsen (SE MI)

Local pickup (MI 48220) is preferred but everything can be shipped commercial UPS/Fedex from MI 48165

Complete bolt in street/track safety seat & harness set:

-2X 17’’ Ultrashield Rally Sport Seats (2014 model) w/ Sunmate Foam Padding & Headrests
-2X IO Port Racing Adjustable Seat Back Braces (SCCA & NASA Legal), pre-drilled for all seat locations.
-2X GForce 6pt Camlock Harnesses (New 9/2014, used three times, have 5pt sub)
-Custom Harness Bar (1.5’’ x 0.120’’ Gr60 seamless DOM Tubing, CNC Laser Cut Brackets, TIG Welded) with aluminum shaft collars. Perfect fit for hard dog roll bars.
-Custom Seat Brackets (3/16’’ Gr60, CNC Laser Cut, No Welds), 5 inches of fore-aft adjustment, adjustments 4 M10 bolts and a pull pin
-Harnesses and seats are properly mounted with Grade 8 & 8.8 fasteners and fender washers at all locations
-Stock seatbelts still integrated for street use, can switch to 6pts in <5 minutes, <1 minute for 5pts (one bolt).

Installed in an ’99 NB. Everything is in great shape and seat covers will be freshly washed for the new owner. Cost me about $1750 originally, I’ll let it go for $1100 as a package. Pickup is highly preferred, but I’ll consider shipping for a serious buyer.

Torsen Differentials:

-4.3 T1 Torsen from a ‘99, 80K miles, no issues, $800 w/ housing, $675 w/o, WTT for 3.6 or 3.9 Torsen

-4.1 T1 Torsen from a ‘94, 80K miles, no issues, $750 w/ housing

All pictures located here:

https://farm5.staticflickr.com/4292/...5e5c76d9_b.jpg

4.1 Torsen
https://farm5.staticflickr.com/4241/...e0aa4411_b.jpg

4.3 Torsen
https://farm5.staticflickr.com/4319/...4881a7ed_b.jpg

PM sent about seat package

What's the layback angle of the seats?

I'm about 20 min away in Milford.

Interested in the seats, local too. Let me know if the sale falls through
​​​​​​​

Adam was nice enough to list these parts on my and another friends' behalf.

The seats are 20° layback. The brackets are approximately 15° layback on top of that for a low head height for 6'0-6'2 drivers in the full rear position. The total angle is about halfway between a sports car and formula car. The angle of the brackets compensates for driver height so shorter drivers aren't much lower in the car. You'll notice in the images that the seat brackets are slotted, which allows shimming the front or rear to tune the angle within reason (some moment is applied to the bolt shank doing this). I'm 6'0 and my helmet is well beneath the roll bar with the 1'' hemispherical padding.

Miyamoto is taking a look at them next week. You're welcome to look at them earlier, but I won't sell them until he has had the opportunity to trial and buy them.

I should add: the driver's seat is centered on the wheel. I think the forward-most positions require some very slight massaging of the tunnel. This can be done with the carpet installed with a rubber mallet and towel.

No worries. I'm not interested in cutting in line.

I would like to take a look at them this weekend if possible. If for no other reason, to see how well I fit in an Ultrashield. I'm pretty sure I'd have to rework the driver bracket. I just barely fit under the broomstick with a fiberglass seat on the floor (no cushion) at a 37* layback. I'm 6'2", but all torso.

Did you make the harness bar yourself, or source it locally?

The plates for the seat brackets and harness bar were laser cut at Superb Fab is South Lyon. The rest is DIY. If you just need a harness bar, the hard dog one is well priced. It made sense to go custom because the seat brackets were already being cut.

You're welcome to stop by. See PM.

Lawd give me the strength not to buy one of those Diffs.

(I might text you this week)

Life is too short for inside wheel spin.

Go for it, Will!

Was any cutting/hammering done to fit these seats? I am looking at the same ones for my car in the future.

17" Ultrashields fit NB no problem- passenger and driver side. Driver side NA may require a hammer to the trans tunnel.
But you can probably use 15" or at worst 16" Ultrashields which will fir NA no problem. If you want to come down to Yardley, PA, you can test-sit in 17" and 16"

Some massaging was required to be both centered on the wheel and to be parrellel with the side plane of the car. The shoulder wings are bent in a little as well where they contact the door.

4.3 Torsen is sold.

4.1 Torsen $700 w/ Housing

Seats, brackets, and harnesses are sold.

Back braces and 4.1 Torsen are still available.