mspnp2 failure from diyautotune?
Hey guys finally broke down and got a megasquirt and wow I was blown away how well my car ran even on the base tune. However after 300 miles something went terribly wrong. I set out on a road trip and about 80 miles in, injectors 1 and 3 were stuck wide open. I reloaded the base tune and nothing. A buddy at the shop i hang out at said it might be a injector driver. Diyautotune has been helpful, but has anyone else had a bad pnp? Were they willing to fix the mistake? Anyways I also checked my entire harness for shorts and it runs ok on the stock ecu. Just a little disappointed for 820 dollars... I guess it could happen
with anything. Also on a side note diyautotune needs a phone number haha! |
We had a supplier change transistors on us without warning to ones that had a slightly different package size. These could contact the case and short out. As soon as we found out about the problem, we came up with a way to fix it, but a couple slipped out before we realized what's going on. Sounds like you got one from that batch. We can get these repaired and turned around in a few days; it's an easy fix. Sorry for the inconvenience.
|
No problem I appreciate the fast response. I'll test it out of the casing, and keep you guys updated. I've been working with Stephen a little bit on the issue. Can't wait to get off work and be able to drive the miata again!
|
Hey just following up I took it out of the case and set it on a antistatic mat. Injectors still stuck. Where should I go from here?
Thanks! Chase |
Hey Matt, are you guys closed for the holidays? Ive sent 3 emails with no response. Hoping to get back on the road soon. Thanks!
|
Originally Posted by claurence42
(Post 1082067)
Hey Matt, are you guys closed for the holidays? Ive sent 3 emails with no response. Hoping to get back on the road soon. Thanks!
|
Originally Posted by Leach0789
(Post 1082398)
I also had not heard anything from Matt since Monday. I got a response today after leaving a voicemail yesterday. I guess one of the techs was on the road all week and the other was dealing with some urgent issues.
|
Just wanted to say that Matt and his team were very helpful and got everything cleared up, even shipped it two day air to CA. Thanks guys!
|
Hacksaw worked for me :)
|
1 Attachment(s)
That was about what the fix was, until we could get a new board spin out.
https://www.miataturbo.net/attachmen...ine=1405691465 You can see the new design uses an internal heat sink (at left) designed for the new packaging. |
curious about this hacksaw fix...
|
Sorry, should have been more descriptive ....
So basically I came across a situation where the MSPNP worked great when not in the enclosure, but as soon as I buttoned it up the car would behave very strangely. This includes rough idle, rich AFR, poor starting, and operational changes with connections/disconnections of the USB cable. I discovered that we were getting battery voltage into the case, which was creating various shorting paths (through the USB cable for example). This is measurable by using a DMM between any of the connector shells to the GND reference. You will see a non-zero voltage. The cause is a TO package mounted to the connector panel (presumably for heat dissipation) shorting the TAB connection to the enclosure close to the screw from the connector panel into the extrusion. I simply used a hack-saw to cut the tab back (on a diagonal) such that the tab no longer made contact with the enclosure when closed. The hacksaw fix damaged the insulation pad under the TO package, so I used electrical tape to provide electrical insulation. It should be noted that I doubt this unit was DOA. It was given to me by a miata buddy who has gone Hydra. I am pretty sure he picked it up pre-owned, so I have to think somebody used it before, with good results. So if your car starts running super rich, and showing operational changes with USB connect/disconnect events, I would look here first. I do not have a picture handy, but if I were to describe the location; it is on the baro sensor side, MS connector panel (not the car side), last TO package in the bank of 4. |
All times are GMT -4. The time now is 02:07 PM. |
© 2024 MH Sub I, LLC dba Internet Brands