Your top tank looks pretty sick. :(
|
naw it's ok. My last radiator cap started leaking a little because the gasket inside rotted. I replaced the cap and sprayed the rad off with a hose, but didn't scrub it down or anything.
|
This and Joe Perez's thread are very helpful but my install is kicking my ass.
I removed the facia support thingy - had to cut some of the plastic fasteners but I don't expect that piece to ever fit back on. I have no way right now to make a support frame for the IC so I'm going to try to locate it approximately supported by a floor jack and then make the metal support. My car has AC so between that and the lower radiator hose plus the turbo drain hose its hard to figure where/ how to tun the hoses.... Tips, tricks and magic spells are greatly appreciated. |
Three year old thread.
|
Originally Posted by Savington
(Post 673620)
Three year old thread.
|
There's no magic to it. I had a bunch of random bends and couplers. Cut to fit and assemble. I did have to remove the stock greddy oil drain pipe when I clocked the compressor down. Replaced it with a tunertoys drain kit and tapped the pan. Not sure if they're still around.
http://img144.imageshack.us/img144/981/1011077zs9.jpg |
Here's another thread, Poobs:
https://www.miataturbo.net/prefabbed-turbo-kits-3/started-mounting-nestercooler-13255/ HTH |
Thanks fellas :)
I think I'll also borrow a chop saw or a large pipe cutter to make things easier. It also looks that as much as I hate to do it the nose needs to come off - no ? |
BTW. This is what I have http://cgi.ebay.com/ebaymotors/CXRac...Q5fAccessories
|
Taking the front bumper on or off a miata sucks.
|
Originally Posted by TurboTim
(Post 673815)
Taking the front bumper on or off a miata sucks.
|
Originally Posted by TurboTim
(Post 673815)
Taking the front bumper on or off a miata sucks.
|
I have my IC all plumbed up. My next door neighbor if a freaking genius!!!! He visualized cuts angles and stuff really well so while he called where to cut I used a chop saw to cut the pipes. It went very fast !!!
I still need to find a way to secure the IC. We had the IC up on a floor jack while we set up the pipes. Where is a good place to buy two couplers and T clamps ? Need a 2&1/2 to 2 inch to connect the pipe to the turbo and a 2&1/2 to 2&1/4 coupler to slap a Cone to the turbo. |
siliconeintakes.com poops
|
Originally Posted by Faeflora
(Post 673933)
siliconeintakes.com poops
Were you guys able to get the nose support and tray under the engine back on after the IC went on ? I jacked up the receiver dryer with my jack to make romm for the IC :giggle: |
Nose support, no, tray yes. I could fit both on if I was more aggressive with the trimming.
|
Originally Posted by kotomile
(Post 673944)
Nose support, no, tray yes. I could fit both on if I was more aggressive with the trimming.
I still have a lot of work to do - still :cry: |
Originally Posted by poobs
(Post 673940)
Thanks. I'm running out of $ so I might have to go with flebay couplers..
Were you guys able to get the nose support and tray under the engine back on after the IC went on ? I jacked up the receiver dryer with my jack to make romm for the IC :giggle: |
Just intercoolers on E-gay tried to screw me $6.00 for a 2 inch T clamp!!!
I bought my couplers from another E-gay vendors and found great prices on clamps on just couplers...oredered. |
All times are GMT -4. The time now is 08:30 PM. |
© 2024 MH Sub I, LLC dba Internet Brands