Turbo Failure? Boost Leak? Bad Gasket? WHAT THE HELL IS THIS SOUND?!
Ok so about a month ago I had just fixed a boost leak with my Jim IC. Went Around Boosting and BLAM I get this screeming/shrieking/BAD sound at 10 vac - 5.5 psi of boost. So I Figure fuck boost leak. Take off Jim's shit and hot-pipe it. Well it is still there. So check all my bolts. Manifold is at like 40 foot pounds. GReddy called for like 37. Used a long vac line around the turbo and the manifold couldnt hear any leaks. Checked to see if turbo was getting oil. It is. No smoke so Im not burning anything. Car pulls hard and hits boost where it should and holds it from like 4-4.5k (full boost) to red-line. Both people agreed it wasnt pinging. I have my Bipes set up to start pulling like 2.5 - whereever pretty soft setting. The LED's say it is working and so does my timing light. (Made it Retard the timing for heat then looked at it with a light and once the car warmed it turned on a light and blam timing went down.) So both the people I gave rides to said it was the Turbo. They said I should check for shaft-play and that TD04's that fail the most are GReddy something on the inside carrier or something. Anyway if anyone has had this happen to them or have any ideas please help me! Oh yeah the turbo has 543 miles on it and I didnt ever hit full boost till after 275 miles and after I re-tightend everything.
|
definately check for shaft play, and check your BOV to make sure its working properly, besides that maybee see if your turbine wheel isnt grinding against anything??
|
Originally Posted by BrokeEnthusiast
(Post 56122)
definately check for shaft play, and check your BOV to make sure its working properly, besides that maybee see if your turbine wheel isnt grinding against anything??
|
maybe a little bit of something got knocked loosed and is being dragged around by one of the sides of your turbo? what kind of intake filter are you using?
|
If the compressor blades were hitting the housing and shrieking then you wouldn't be making boost.
does it sound like this (shrieking): http://www.magnaflowonline.com/catal...load/spool.wmv or does it just sound like a buzzing/whining noise? Can the sound be created at idle when bliping the throttle? Can you record a sound clip; phone, dig. camera, "Talkboy"? |
damn- I forgot about that. Nasty!
|
Originally Posted by braineack
(Post 56155)
If the compressor blades were hitting the housing and shrieking then you wouldn't be making boost.
does it sound like this (shrieking): http://www.magnaflowonline.com/catal...load/spool.wmv or does it just sound like a buzzing/whining noise? Can the sound be created at idle when bliping the throttle? Can you record a sound clip; phone, dig. camera, "Talkboy"? |
Originally Posted by underconstruction
(Post 56148)
maybe a little bit of something got knocked loosed and is being dragged around by one of the sides of your turbo? what kind of intake filter are you using?
|
I'm going to with leak then, make sure all your couplers are dag-nasty tight.
|
Originally Posted by braineack
(Post 56212)
I'm going to with leak then, make sure all your couplers are dag-nasty tight.
|
i know what it sounds like and i dont have to hear it because my symptoms are exactly the same and from the looks of it it seems that the shaft on mine has warped not good it will make a ticking noise at -10 and at 0 its more of a tiking noise and at +5 onwards its a screaching but ticking noise am i right ????
|
ticking is usually an exhaust leak. screaching/whining/whistling is usually a boost leak.
|
Originally Posted by aldj1983
(Post 56224)
i know what it sounds like and i dont have to hear it because my symptoms are exactly the same and from the looks of it it seems that the shaft on mine has warped not good it will make a ticking noise at -10 and at 0 its more of a tiking noise and at +5 onwards its a screaching but ticking noise am i right ????
|
bought the car 2nd had with the turbo installed so i just got to buy new shaft or turbo but think i will get the water cooled one if i have to buy whole thing
-al- edit i am going to strip the turbo down again and double check it is the shaft also check the turbine wheel for damage as mine had verry slight bent marks on the edges of the fins (wouldent notice unless actually looked for ) |
forgot to say living in the uk it is a right bugger getting parts for the turbo
|
so checked the shaft play and there is none in and out and back and forth and up and down is like zero you have it really push on it to make it move side to side or up and down even a tiny bit at all... (friend with a DSM and lots of turbo cars said this is normal) checked all couples none have rips and all where hella monkey tight down. uhhhh yeah so... wtf? Check Throttle Body leaks?
*EDIT* Friend with DSM came over and wiggled it and said it was close to being a lot of shaft play so i was a tard... going to call GReddy and yell at them lots. |
i want a sound clip. shaft play will cause the blades to hit the compressor housing walls. The video I posted is what that sounds like. plus you wont be able to make boost.
|
Originally Posted by braineack
(Post 56261)
i want a sound clip. shaft play will cause the blades to hit the compressor housing walls. The video I posted is what that sounds like. plus you wont be able to make boost.
|
sweet little video braineack. The thumbs down is the icing on the cake.
|
ive just dremeled about 0.2mm from each blade on the turbine and all the noise has gone completely ..
|
All times are GMT -4. The time now is 12:51 AM. |
© 2024 MH Sub I, LLC dba Internet Brands