Purge Valve Solenoid
#1
Purge Valve Solenoid
Does anybody know or have experience with purge valve solenoids? I have one on my 90 w/ MSPNP and currently use the purge valve solenoid from the charcoal canister to kick up my idling when A/C is turned..I know I know A/C is for wimps but I'd rather cruise in comfort than sweat my *** off.
I also have the BMW TPS and its been dyno tuned profesionally and have no issues with stalling when AC is on..however I can feel the solenoid doesn't react quite fast enough to catch the compressor. As you can see in my picture I have it plugged into the TB and as I said works pretty good, but I'm looking for one that leaks air quicker and with more volume...anybody know a good one to use? TIA
I also have the BMW TPS and its been dyno tuned profesionally and have no issues with stalling when AC is on..however I can feel the solenoid doesn't react quite fast enough to catch the compressor. As you can see in my picture I have it plugged into the TB and as I said works pretty good, but I'm looking for one that leaks air quicker and with more volume...anybody know a good one to use? TIA
#6
I identify as a bear.
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,109
Total Cats: 6,640
There are plenty of other air solenoids available, some of which are intended specifically to be used as fast-idle valves. I only chose the purge valve initially because it's something that everybody already has.
#8
I just wrote some code that adds a fast idle input. You can connect the AC or blower inputs to it. When the input goes low, it changes the idle target to the fast idle speed. It works on the stim, but the battery on my laptop died before I got a chance to test it on the car.
Do you think I'd be better off raising the idle speed, or increasing the minimum dc?
I don't have AC, and I've never actually tried to use the heater in my car (with the MS). My car idles fine. I'm just doing this for you guys.
Do you think I'd be better off raising the idle speed, or increasing the minimum dc?
I don't have AC, and I've never actually tried to use the heater in my car (with the MS). My car idles fine. I'm just doing this for you guys.
#9
I identify as a bear.
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,109
Total Cats: 6,640
I'd think that both would be ideal.
Raising MinDC will give you an immediate burst of idle accel, whereas relying upon idle speed alone will still give it a chance to stall while the idle routine slowly ramps up DC to seek the new target.
Meanwhile, raising target idle will keep is smooth once it's back into stable closed-loop, without you having to raise minDC so high that it never climbs above it.
Oh, and major props on the software mod. I've never ventured into editing the code. Which release did you use as the base?
Raising MinDC will give you an immediate burst of idle accel, whereas relying upon idle speed alone will still give it a chance to stall while the idle routine slowly ramps up DC to seek the new target.
Meanwhile, raising target idle will keep is smooth once it's back into stable closed-loop, without you having to raise minDC so high that it never climbs above it.
Oh, and major props on the software mod. I've never ventured into editing the code. Which release did you use as the base?
#10
I've been running a slightly modified version of hr_10g on my car for a while, so that's what I used. It would be simple to port it to 11c2 or whatever everybody runs here.
I made another change that seemed to resolve the idle droop issue on my car (stalls when coming to a stop). I have both TPS inputs going to the cpu (TPS 1N and 2L). The cpu artificially sets the tps values:
0v = no throttle
2.5v = partial throttle
5v = full throttle
I need to do more testing though.
I'll go ahead and play around with different minimum DC steps, and see how it handles heater + headlights, then I'll post a firmware for you guys to try.
If you have any other ideas, let me know!
PS What inputs do you recommend? My car is not setup like everybody elses, so I'm not sure what inputs you guys have leftover.
I made another change that seemed to resolve the idle droop issue on my car (stalls when coming to a stop). I have both TPS inputs going to the cpu (TPS 1N and 2L). The cpu artificially sets the tps values:
0v = no throttle
2.5v = partial throttle
5v = full throttle
I need to do more testing though.
I'll go ahead and play around with different minimum DC steps, and see how it handles heater + headlights, then I'll post a firmware for you guys to try.
If you have any other ideas, let me know!
PS What inputs do you recommend? My car is not setup like everybody elses, so I'm not sure what inputs you guys have leftover.
#11
I then get a delay circuit and put it in between the solenoid and the A/C compresser. So I switch on the A/C, then the solenoid get powered immediately, the delay circuit will provide power to the A/C compresser after 2 second.
So the rpm will first raise up to 1200rpm slowly and then drop to 950rpm.
However sometimes in very hot condition, the air provided by 2 solenoids is still not enough to maintain a stable idle. Since the resistance made by the compressor is somehow increased with temperature.
#12
The code has been tested, and I moved it over to a "clean" version of hr_10g (attached). At this point, all it does it wait for JS4 to go low, and it changes the idle speed to whatever you have set for your Fast Idle Speed RPM.
I tested turning on headlights & blower at the same time, and it was able to prevent a stall every time. The idleDC increases quickly and catches it. The downside is that when you turn the A/C off, the idleDC drops quickly, and temporarily increases your idle speed (with my tune, at least).
I haven't messed around with changing the minimum DC yet. It would be a bit more complicated, but I will do it next week. I'm not sure it's necessary, since the idleDC increases quickly on it's own due to the increased idle setpoint... but we'll see.
For testing, I wired it to a switch. You'll want to wire it to the A/C input (1Q) or the blower input (1S). Both of those go low when switched on, and are 12v while off. So you'll need to use a voltage divider to keep it below 5v.
I'm sure there is a "smoother" way to do this. In fact... it might work better in open loop mode. But I like to start with the simple things first
Joe - Feel free to split this thread up if you want. This really doesn't have anything to do with the purge solenoid, although we both have the same final goal in mind.
I tested turning on headlights & blower at the same time, and it was able to prevent a stall every time. The idleDC increases quickly and catches it. The downside is that when you turn the A/C off, the idleDC drops quickly, and temporarily increases your idle speed (with my tune, at least).
I haven't messed around with changing the minimum DC yet. It would be a bit more complicated, but I will do it next week. I'm not sure it's necessary, since the idleDC increases quickly on it's own due to the increased idle setpoint... but we'll see.
For testing, I wired it to a switch. You'll want to wire it to the A/C input (1Q) or the blower input (1S). Both of those go low when switched on, and are 12v while off. So you'll need to use a voltage divider to keep it below 5v.
I'm sure there is a "smoother" way to do this. In fact... it might work better in open loop mode. But I like to start with the simple things first
Joe - Feel free to split this thread up if you want. This really doesn't have anything to do with the purge solenoid, although we both have the same final goal in mind.
Last edited by JustinHoMi; 07-27-2009 at 04:36 PM.
#13
These solenoids were designed for a different purpose, so Joe if you know of this particular solenoid you speak of it would be greatly appreciated. thanks
#15
Senior Member
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
Am I understanding correctly that some of you are looking for a more suitable solenoid? I know older Toyotas used A/C idle up solenoids that they sometimes refer to as a VSV (vacuum switching valve). Don't know if they'd work any better than our purge solenoids, but at least they were originally used for our intended purpose. I don't think they still make the same old part for my 25-y.o. 4runner but some of the Toyota truck guys report successful replacement with Toyota part number 88690-32280, which is originally for a Camry. You can buy that one from a dealer (Jay Marks out of Houston is a good outfit) or just try pulling one from a bone yard, should be plenty of them in random Toyotas.
#18
Am I understanding correctly that some of you are looking for a more suitable solenoid? I know older Toyotas used A/C idle up solenoids that they sometimes refer to as a VSV (vacuum switching valve). Don't know if they'd work any better than our purge solenoids, but at least they were originally used for our intended purpose. I don't think they still make the same old part for my 25-y.o. 4runner but some of the Toyota truck guys report successful replacement with Toyota part number 88690-32280, which is originally for a Camry. You can buy that one from a dealer (Jay Marks out of Houston is a good outfit) or just try pulling one from a bone yard, should be plenty of them in random Toyotas.
Yes I have that solenoid as well as one from a Mitsubishi V6 and still the purge valve from the Miata leaks air most.
I'm now thinking maybe looking into Chevy's, Ford's etc..
I just wished DIY or somebody could build in a dedicated circuit for the MSPNP to address A/C.