Upgraded Greddy turbo kit
#1
Junior Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (2)
Join Date: Jul 2011
Location: Houston, Tx
Posts: 167
Total Cats: 4
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Up for sale is an upgraded Greddy turbo kit for the 1.6. Only selling because I'm building a 1.8.
What you get:
Looking to get $1000 shipped OBO. Willing to trade for 5 or 6 speed, forged rods, Torsen LSD. Let me know if you have any questions. Located in Houston, Tx. Thanks for looking!
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100806-upgraded-greddy-turbo-kit-1o6ey3j.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100807-upgraded-greddy-turbo-kit-lbjojfl.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100808-upgraded-greddy-turbo-kit-tvuriy8.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100809-upgraded-greddy-turbo-kit-6vr2rbl.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100810-upgraded-greddy-turbo-kit-3pvnfy2.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100811-upgraded-greddy-turbo-kit-tlainlc.jpg?dateline=1390599607)
What you get:
- Original Greddy - Very minimal shaft play.
- Original Greddy manifold - A relief cut was made down the middle of the flange. I found this to be unnecessary as I had no cracking issues and no warping issues. The manifold slid right off the studs. I believe this was a fix Greddy made on their later kits.
- ARtech 2.5" SG Downpipe - Bought this brand new so it was only used for 3,000 miles or so. Has bung welded for stock O2 sensor which I blocked off with a plug when I switched to Megasquirt. Also has WBO2 bung welded at the end of the pipe. Beautiful piece
- Ebay intercooler core - Custom aluminium bracket and tapped for IAT.
- -10 Oil drain - Flange and fitting off the turbo were from ARtech. Drain line was made by me using Aeroquip fittings and line.
- Original Greddy oil feed
- Wastegate actuator and bracket - I made a custom bracket out of a strip of aluminium because I clocked the turbo with the compressor outlet pointing down.
- Intake pipe & filter - I used a 2.25" to 2.5" coupler off the turbo inlet to a 2.5" pipe. Electrical tape was used to increase the OD of the pipe to slide a 3" filter on. Kind of ghetto but it got the job done.
- Stock 1.8 tan top injectors - One broken clip on one of them.
- All the bolts and nuts that I used, labeled appropriately.
- Original Greddy downpipe
Looking to get $1000 shipped OBO. Willing to trade for 5 or 6 speed, forged rods, Torsen LSD. Let me know if you have any questions. Located in Houston, Tx. Thanks for looking!
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100806-upgraded-greddy-turbo-kit-1o6ey3j.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100807-upgraded-greddy-turbo-kit-lbjojfl.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100808-upgraded-greddy-turbo-kit-tvuriy8.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100809-upgraded-greddy-turbo-kit-6vr2rbl.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100810-upgraded-greddy-turbo-kit-3pvnfy2.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100811-upgraded-greddy-turbo-kit-tlainlc.jpg?dateline=1390599607)
![](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/100812-upgraded-greddy-turbo-kit-fcbmimc.jpg?dateline=1390599607)
Last edited by albertogti117; 01-28-2014 at 06:18 AM.
#7
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM