LFX Build Thread
#1
LFX Build Thread
Far enough along to start the build thread as I've had a couple PMs asking about progress.
1993 Miata. Keeping the shell, hardtop, shocks... not much else!
Gutted the car- nearly everything came out. LOTS of cleaning, painting, etc. In fact, only the gas tank remained- 180lbs+ of stuff not going back in the car (not including the seats, steel hood, pdf, exhaust..). I re-did the suspension: blast/ paint/ new bushings/ new bearings/ blueprinted hubs/ and installed Zerks. I've got a full brake package ready to install. V8R sent me the diff mount- it's installed and bolted up (Getrag G80 LSD with a 3.4 gear). The '12 Camaro LFX and 6spd is in the garage, as is a new alternator, computer, gas pedal and starter (eng came stripped). I've ordered new bolts from GM but it takes a MONTH to get the bolts. The engine mount kit, clutch kit, and fuel kits have been ordered and are in production. Also ordered the stage 2 rear end kit and aluminum driveshaft. I've got a fiberglass hood with integrated headlight covers inbound. I'm keeping the Boss Frog roll bar but will cage at some point in the future.
The car will mostly be a track toy and as such will have no radio, heat, AC, wipers, headlights... yada yada. But I'd like to be able to drive it on occasion, and want it to look finished- difference between built intentionally light and built cheap- so I am installing new carpeting and re-did the door panels with ABS and alcantara. Right now, I can pick up the car with my hands. The seat is a Sparco Pro 2000 carbon fiber with a PCI adjustable mount. I have a second mount and am searching for a passenger seat. Wheel is a suede Momo, wheels are 9' 6UL.
Still to buy: Clutch (replacing the OEM), hiring harness, safety harness, battery, Aim MXL dash, switches, brake line (-2an)... and I need to figure out how to run/ design the belt as I'd like to eliminate the power steering pump and ac pulleys. Wiring is another challenge...
I'm stuck now, waiting for parts. Will update this thread as the project continues.
As it sits now:
Diff Mount:
Has to be 1.5' up
Brakes/ control arms:
Door Panels:
Running Fatcat Bilsteins:
Engine & Trans:
Seat:
Boxes of removed stuff:
Started here...
Adios!
1993 Miata. Keeping the shell, hardtop, shocks... not much else!
Gutted the car- nearly everything came out. LOTS of cleaning, painting, etc. In fact, only the gas tank remained- 180lbs+ of stuff not going back in the car (not including the seats, steel hood, pdf, exhaust..). I re-did the suspension: blast/ paint/ new bushings/ new bearings/ blueprinted hubs/ and installed Zerks. I've got a full brake package ready to install. V8R sent me the diff mount- it's installed and bolted up (Getrag G80 LSD with a 3.4 gear). The '12 Camaro LFX and 6spd is in the garage, as is a new alternator, computer, gas pedal and starter (eng came stripped). I've ordered new bolts from GM but it takes a MONTH to get the bolts. The engine mount kit, clutch kit, and fuel kits have been ordered and are in production. Also ordered the stage 2 rear end kit and aluminum driveshaft. I've got a fiberglass hood with integrated headlight covers inbound. I'm keeping the Boss Frog roll bar but will cage at some point in the future.
The car will mostly be a track toy and as such will have no radio, heat, AC, wipers, headlights... yada yada. But I'd like to be able to drive it on occasion, and want it to look finished- difference between built intentionally light and built cheap- so I am installing new carpeting and re-did the door panels with ABS and alcantara. Right now, I can pick up the car with my hands. The seat is a Sparco Pro 2000 carbon fiber with a PCI adjustable mount. I have a second mount and am searching for a passenger seat. Wheel is a suede Momo, wheels are 9' 6UL.
Still to buy: Clutch (replacing the OEM), hiring harness, safety harness, battery, Aim MXL dash, switches, brake line (-2an)... and I need to figure out how to run/ design the belt as I'd like to eliminate the power steering pump and ac pulleys. Wiring is another challenge...
I'm stuck now, waiting for parts. Will update this thread as the project continues.
As it sits now:
Diff Mount:
Has to be 1.5' up
Brakes/ control arms:
Door Panels:
Running Fatcat Bilsteins:
Engine & Trans:
Seat:
Boxes of removed stuff:
Started here...
Adios!
#7
Interior work closer to being done, new clutch/ flywheel installed as was the new alternator and starter. Picking up a belt today (no a/c). Installed V8R upper ball joints, picked up an AIM MXL Pro which, when attached to the Delphi MEFI-5 will have the following items that can be logged:
ECU_1 5B_RPM RPM
ECU_2 5B_SPEED Speed
ECU_3 5B_TPS Throttle position
ECU_4 5B_PPS Pedal position
ECU_5 5B_ECT Engine coolant temperature
ECU_6 5B_FUEL_T Fuel temperature
ECU_7 5B_MAT Manifold air temperature
ECU_8 5B_MAP_VOLT Manifold air pressure voltage
ECU_9 5B_MAP Manifold air pressure
ECU_10 5B_OIL_P Oil pressure
ECU_11 5B_FUEL_P Fuel pressure
ECU_12 5B_IGN_VOLT Ignition voltage
ECU_13 5B_EGR_FB Engine gas recirculation voltage
ECU_14 5B_INJ_BANKA Injection pulse bank A
ECU_15 5B_INJ_BANKB Injection pulse bank B
ECU_16 5B_SPARK_ADV Spark advance
ECU_17 5B_KNOCK_RET Knock retard
ECU_18 5B_CAM_RET Camshaft retard
ECU_19 5B_FUEL_CONS Fuel consumption
ECU_20 5B_ENG_LAMP Engine malfunction indicator
ECU_21 5B_RTM_H Run time hour
ECU_22 5B_RTM_M Run time minute
Fuel kit and subframe should be here next week!
ECU_1 5B_RPM RPM
ECU_2 5B_SPEED Speed
ECU_3 5B_TPS Throttle position
ECU_4 5B_PPS Pedal position
ECU_5 5B_ECT Engine coolant temperature
ECU_6 5B_FUEL_T Fuel temperature
ECU_7 5B_MAT Manifold air temperature
ECU_8 5B_MAP_VOLT Manifold air pressure voltage
ECU_9 5B_MAP Manifold air pressure
ECU_10 5B_OIL_P Oil pressure
ECU_11 5B_FUEL_P Fuel pressure
ECU_12 5B_IGN_VOLT Ignition voltage
ECU_13 5B_EGR_FB Engine gas recirculation voltage
ECU_14 5B_INJ_BANKA Injection pulse bank A
ECU_15 5B_INJ_BANKB Injection pulse bank B
ECU_16 5B_SPARK_ADV Spark advance
ECU_17 5B_KNOCK_RET Knock retard
ECU_18 5B_CAM_RET Camshaft retard
ECU_19 5B_FUEL_CONS Fuel consumption
ECU_20 5B_ENG_LAMP Engine malfunction indicator
ECU_21 5B_RTM_H Run time hour
ECU_22 5B_RTM_M Run time minute
Fuel kit and subframe should be here next week!
#15
Far enough along to start the build thread as I've had a couple PMs asking about progress.
1993 Miata. Keeping the shell, hardtop, shocks... not much else!
Gutted the car- nearly everything came out. LOTS of cleaning, painting, etc. In fact, only the gas tank remained- 180lbs+ of stuff not going back in the car (not including the seats, steel hood, pdf, exhaust..)...
1993 Miata. Keeping the shell, hardtop, shocks... not much else!
Gutted the car- nearly everything came out. LOTS of cleaning, painting, etc. In fact, only the gas tank remained- 180lbs+ of stuff not going back in the car (not including the seats, steel hood, pdf, exhaust..)...
#17
I am interested in this as well. So I was doing a little googling and found another thread where you asked about a tensioner bracket without the A/C and P/S. I would look at supercharger tensioners.
This looks like an V8, but the idea is still valid.
New Tensioner, Major help for belt slippage on 2300. - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
It looks like the LFX superchargers are all centrifugal type and rely on the movement of the supercharger to tension. However, you may be able to get something together with the above company.
This looks like an V8, but the idea is still valid.
New Tensioner, Major help for belt slippage on 2300. - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
It looks like the LFX superchargers are all centrifugal type and rely on the movement of the supercharger to tension. However, you may be able to get something together with the above company.