Brake duct inlets for NB's
#2
Good idea.
Here's a few additional suggestions:
The top of the foglight recess is flat so you will get a better fit if you flatten the top:
I bought a set of DemonTweaks Air Ducts and trimmed them to fit:
Note: The Demon Tweaks grilles mount to the flat ridge in the duct.
I also made a backplate for the rear so that the pop-rivets have something to hold onto (they'd pull-through the bumper).
If you're attaching via bolts, you can probably just get away with large washers on the bolts since you don't want then to "pull through":
I would've liked the ducts to be deeper so that there was a longer section to clamp the hose to, mine are barely the width of a clamp:
Your ducts need to have a parallel section at the rear, not tapered, for the hose clamps to mount securely, otherwise they'll slip off.
Here's a few additional suggestions:
The top of the foglight recess is flat so you will get a better fit if you flatten the top:
I bought a set of DemonTweaks Air Ducts and trimmed them to fit:
Note: The Demon Tweaks grilles mount to the flat ridge in the duct.
I also made a backplate for the rear so that the pop-rivets have something to hold onto (they'd pull-through the bumper).
If you're attaching via bolts, you can probably just get away with large washers on the bolts since you don't want then to "pull through":
I would've liked the ducts to be deeper so that there was a longer section to clamp the hose to, mine are barely the width of a clamp:
Your ducts need to have a parallel section at the rear, not tapered, for the hose clamps to mount securely, otherwise they'll slip off.
#3
Good feedback man.
I suppose i could flatten the top to get a few more MM of clearance. I just used 4 3mm machine screws to hold the inlet into the bumper.
My 2.5" hose has not arrived yet so i haven't got a chance to test-fit. I agree my taper at the exit may be insufficient - i added a little extra flare at the end which is hard to see so the hose clamp stays put.
I wanted to make sure i had an integrated screen to help prevent rocks and rubber at the track from entering the ducting and potentially tearing a hole.
Great job with your DIY btw.
I suppose i could flatten the top to get a few more MM of clearance. I just used 4 3mm machine screws to hold the inlet into the bumper.
My 2.5" hose has not arrived yet so i haven't got a chance to test-fit. I agree my taper at the exit may be insufficient - i added a little extra flare at the end which is hard to see so the hose clamp stays put.
I wanted to make sure i had an integrated screen to help prevent rocks and rubber at the track from entering the ducting and potentially tearing a hole.
Great job with your DIY btw.
#5
I spend a lot of time at the track and know especially when i'm behind someone on slicks i get a lot of rubber thrown at me. My big concern was having a duct get compromised then somehow damage a brake line. I saw a video recently of an EVO that had a brake duct get wrapped around a front axle, tear a brake line, lost all hydraulic pressure and then crashed due to no brakes. Obviously we don't have a front axles to deal with but when it comes to potential avoidable safety issues i thought this was cheap insurance and should prevent larger debris from entering the ducts.
#6
Not a great photo, but the best I have at the moment.
I used an aluminum duct flange from Aircraft Spruce.
ALUMINUM FLANGES FOR DUCTING from Aircraft Spruce
I used the 4" to 3" flange, connected to a 3" to 2.5" straight silicone reducer, with a short piece of 2.5" aluminum tubing to connect the reducer to the 2.5" duct.
The 4" flange fills the fog light hole well.
The silicone reducer is sandwiched against the backside of the bumper cover with a couple of thin aluminum "L" brackets for a tight fit with no holes to drill.
#8
As aidandj pointed out, the mesh will block a lot of air (supposedly household flyscreen mesh blocks 50% of airflow in your house).
The foglight recess will be a high pressure area when moving though so you're still getting a lot of air through it (ie. much more than 50%).