How Much HP Can I Expect 1.6-M45
My 93 is primarily my track (HPDE) car.
Has JR M45 with boost kit Stock injectors Water Injection TDR CAI Crank pulley overlay that came with the JR Boost Kit Had it dynoed about 2 years ago. 2 runs both at 139hp. My 1st question is, is this typical power for my set up? A buddy is installing TDR air/air intercooler and an oil cooler this week. I am also considering a smaller SC pulley. Does this make sense in my effort to maximize the power out of this set up. If the pulley will help, what size pulley should I get. Is there anything else I should be looking at, maybe bigger injectors? Thanks. |
mwest, you're going to want to put on your thick skin. even though this may be a legitimate question/post, it's functionally equivalent to trolling as far as the readers of this site are concerned.
|
I don't know....sounds about right to me.
LOL @ 139whp. I should shut up since you actually use your car on the track. If you think you're down on power then spend some time tuning. Regardless of what someone tells you is about right or not...if you are hitting the proper AFR targets and timing is advanced but a few degrees short of detonation then you've got the best easy street tune you can put on it. Besides that hit a steady state dyno and actually find MBT. |
No bandaids? No fuel or spark modification at all??
Haven't seen many dyno sheets from 1.6 M45s but that sounds about right. Found a dyno plot on FM's website about a 1.6M45 upgraded to one of their turbo setups, has about the same power: http://www.flyinmiata.com/tech/dyno_...odooII_1.6.pdf |
I'd say ditch that wimpy lil whinebox and get a turbo like a man
but I'm sure you already know that being on miataTURBO.net:D |
I was expecting to get more of a "GET A TURBO" response. So, this was pretty mild.
I'd considered a Turbo before I got this set up. I thought the turbo would be too much work for me. I am not a greahead. I do the basics on my car, brakes, rotors, fluids etc. The simple stuff. Right or wrong I was led to beleive Turbo's would require more input on my part. I really enjoy driving, but not so much the getting under the car. I thought the SC would be a bit easier to deal with. But, like everyone else now I'm searching for a bit more power and I was never able to get a straight answer as to whether I'm getting all I can out of this set up. I'm still trying. Thanks. |
Hmm...still no answers on engine management.
Hard to know what your setup is capable of without knowing your tuning limitations. |
gospeed81,
My buddy has my car now and is going over it re: getting ready for the track. Have my 1st track days of the season coming up Mid-April. He's an outstanding tuner. He is first going over everything from a reliability safety perspective. He's never worked on my car before so he's getting familiar with the base set up. Then installing the air/air intercooler, re-locating the oil filter and adding an oil cooler. Then it's on to maximizing the power. I've heard various comments about going to a smaller pulley and larger injectors. But, not sure if that's right for my set up & what the gain if any would be by doing that. Instead of a gain in performance, would I be gaining more agg. I was hoping some of the guys here would have some experiece with a set up like mine. Thanks. |
I made 133rwhp with a sebring (msd) timing box. My engine was a little tired. The sc was a great solution at the time since I was just looking for something to make the 1.6 a better daily driver (more torque). I'm speculating, but if you find yourself wanting a "little" more power now, that feeling won't go away until you've reached the upper limit of reliable power on a stock engine. If that's a remote possibility, then you're better off selling the sc as kit and going with a turbo. IMO, having been through both routes of boost, the turbo is not nearly as complicated as it appeared from the SC side of things.
|
Well, it's hard to know what "tuning" will entail without knowing what you are using to modify fuel delivery and spark timing.
I'd imagine it's a bandaid setup, with some kind of timing retard box and an adjustable fuel pressure regulator. Unless you have real engine management, and bigger injectors you won't get far. The intercooler will help, and allow a little more timing before det sets in. |
with a 1.6 and a measly m45 I think you're doing ok for power. Wouldn't expect it to put out much more. now is that 139HP or 139WHP?
|
18psi:
I was led to believe that's 139 to the wheels. Torque was:134. This was on a DynoJet. gospeed81: The guy who owned the car before me was a NASA engineer for whatever that's worth. Used it as a weekend fun car. Everything was pristine. All the upgrades were precisely done and fully documented. That's why I got it. The price was right but everything was done right. It had the full JR M45 set up. MSD timing, water injection, it had everything it was supposed to have. I added the JR Boost Kit, then tore out the: AC, PS, Cruise, steering wheel, conv. top etc. As I said earlier I know very little regarding the technical aspects of FI. I rely on guys like you on this site and the guys I meet at the track for help and guidance. Little by little I'm learning. |
i have one as well except its only boosting 2psi for some odd reason so no help from me here. im wodering though u mentioned boost kit, from what ive found ive only found the boost kit for the 1.8's not the 1.6's....
do u know more about that boost kit. And yes like they have said with a MS or some tuning im sure u could squeeze out a bit more power specially with water injection... |
Originally Posted by oscargarza88
(Post 545607)
i have one as well except its only boosting 2psi for some odd reason so no help from me here. im wodering though u mentioned boost kit, from what ive found ive only found the boost kit for the 1.8's not the 1.6's....
do u know more about that boost kit. And yes like they have said with a MS or some tuning im sure u could squeeze out a bit more power specially with water injection... If coldside belt must be slipping, if hotside check couplers in addition to belt. |
Originally Posted by gospeed81
(Post 545608)
Hotside or cold side?
If coldside belt must be slipping, if hotside check couplers in addition to belt. hotside. I posted a thread about this on M.net and checked and replaced belt all couplers , bypass valve and some other things. What is next is for me to check the rotors since someone said that the coating on it could be worn and not building boost??? i dunno im lost |
Originally Posted by oscargarza88
(Post 545610)
hotside.
I posted a thread about this on M.net and checked and replaced belt all couplers , bypass valve and some other things. What is next is for me to check the rotors since someone said that the coating on it could be worn and not building boost??? i dunno im lost Those are so simple there's not a lot to diagnose. Not like a turbo with wastegate creep and whatnot. If it's turning with engine, and none of it's leaking, then efficiency is way down. 2psi is ridiculous, I'm assuming you bought it used. Even then, you should be seeing more. Maybe double check routing on bypass valve. Seems that it would stay closed before staying open...but worth a shot. |
Originally Posted by gospeed81
(Post 545612)
Yeah, must be a worn unit.
Those are so simple there's not a lot to diagnose. Not like a turbo with wastegate creep and whatnot. If it's turning with engine, and none of it's leaking, then efficiency is way down. 2psi is ridiculous, I'm assuming you bought it used. Even then, you should be seeing more. Maybe double check routing on bypass valve. Seems that it would stay closed before staying open...but worth a shot. And i have a STI so i know all bout turbo problems, new to SC hence the confusion. I actually zip tied the bypass valve closed to get it out of the picture and still only 2psi. the interesting thing is that in any gear if i let vacume build up then floor it real quick it goes up to 5-6 psi for like .25 sec then goes back down to 2psi or so. hey at least its consistent haha |
Sounds like boost leak.
Is your idle high? Fill in your sig line with mods, including engine management, and put your location in your profile...makes it easier to help. It's also forum ettiquette to start an intro thread in the Meet n' Greet section. |
Originally Posted by gospeed81
(Post 545625)
Sounds like boost leak.
Is your idle high? Fill in your sig line with mods, including engine management, and put your location in your profile...makes it easier to help. It's also forum ettiquette to start an intro thread in the Meet n' Greet section. Oh ok thanks i will do that then, im not on this forum very much since obviouslly its mainly a turbo forum but still get good info on here on susp and engine mang mainly. And from the few threads i read on the SC section its mostly get a turbo!! haha which is understandable... As for EM i honestly not entirelly too sure, im pretty sure it has a power card but other than that nothing. im saving up for a MS, that should help quite a bit. And if there are no leaks on the crosspipe section connecting the SC to intake manifold then where else could there be one? thanks i appreciate the help!! |
I've opted to replace my 1.6 M45 set up for a 1.8 bored out to 2.1, balanced and blue printed. With a 99 head and new header plus other accessories, expecting to get about 170rwhp, naturally aspirated. This should give me much fewer hassles on the track. Will be starting the swap mid-June. Plan is to get more power with less agg. More time on the track less time under the car.
|
oscargarza88,
They did offer a boost kit for the 1.6-M45. It included a pulley that fit over the crank pulley as well as a smaller supercharger pulley, the belts and some engine management electronics. All the searching I've done seems to reinforce that my 139-140hp is about right for my set up. But, as I mentioned in my previous post I'm moving on to a 1.8 bored out to 2.1. Looking for greater reliability on track. |
Sounds awesome. I'm running a 1.8 with the M45 and water to air intercooler, 10:1 compression, Adaptronic and pushing out 167hp @ wheels. That N/A build sounds like the go.
|
sabatoeur,
Australia? That's odd, I don't denote any accent on your post. Looking forward to getting there 1 of these days. On the list of things to do. I just instructed one of your countrymen on the track last week, a Porsche event at a track in NJ, USA. It's sounds like you're getting decent power from your set up. If my car were a street car it would be fine-but on track it's been a PITA. I really want to stick with the Miata because I enjoy driving it and it's one of the least expensive cars to track. I am luckily enough to drive pretty much what I want on track up to maybe $75-$100k. But, for me it's just about fun and I can't justiy going to a Vette, Porsche or whatever for 20-30 track days a year. My other fun cars are a 350Z conv., a 300zx conv., a boxster, 66 Mustang conv. and a 64 230sl conv.This is not my life but it's something I really enjoy. To keep it in perspective a Miata is a perfect car for me. I run with various Porsche, Vette and independent track clubs. I'm in the instructor group so there are some very good drivers and some very fast cars. A stock 1.6 is OK but a bit more power makes it more fun. The 1.6 & M45 keeps me from getting completelt run over but a bit more would be better. But over the years I keep running into nagging SC related problems that run into my track time and fun factor. So, this 1.8 to 2.1 conversion sounds like it could be the answer. I am optimistic this will work. Conversion is to start mid-June and I'll be back on the track Mid-July. Will keep you posted. |
sabatoeur,
I forgot to ask you, do you ever track your car? Do you do much tweaking with the Magasquirt? |
Originally Posted by oscargarza88
(Post 545607)
i have one as well except its only boosting 2psi for some odd reason so no help from me here. im wodering though u mentioned boost kit, from what ive found ive only found the boost kit for the 1.8's not the 1.6's....
do u know more about that boost kit. And yes like they have said with a MS or some tuning im sure u could squeeze out a bit more power specially with water injection... You dont need a kit. There are many companies who build custom pulley either for the blower snout or the crank. This is your calculation (Crank pulley size / Blower pulley size x step up ratio) x max rpm. I maxed out a M45 unit I had years ago just under 16k rpm. Boost means nothing for a blower. How efficient your pump (blower) flows will dictate boost (what TB size, boost tube size, IM etc). That said as someone else mentioned, I would also look into your bypass to ensure that the lobe housing is seeing enough pressure from a closed bypass. It is possible that the bypass could be stuck open or the rod from the bypass is hitting something. *edit* Saw you moved on....oh well. Did ou ever figure out the problem? |
You can see the boost kit on Moss Motors site. I've moved on. I just bought Monster Miata set up by Martin Wilson. It's got appox:325rwhp. Car is coming from Ca. Once I've driven it on track and I like it or don't like it--I'll decide what I'm going to do with my 1.6.
|
imo if you stay with the super get a mp62 that lil m45 is just way to small.
|
magmamx-5,
I think I'd rather have a V-8. Got a Martin Wilson prepped Monster 302 from Ca. Arriving this Friday. |
If I had a chice between a V8 and an SC I would need about .1 seconds to decide which to go with. I would also keep in mind that AL blocks for the Windsor family are finnaly starting to get affordable and that the LSX engines are also nice and light-weight too.
|
I was at the Carlisle Import and Kit Car Show this past weekend. This may be the largest show of it's type in the country. Huge turnout in general. There was 1 guy with a V8. LS1 with some modifications. Dynoed at 380rwhp. The guy did the build himself. Incredibly clean and professional. This was his 3rd year at the show.Drives the car from Michigan to Carlisle, Pa. My 302 is due here Friday and I'm scheduled to be on the track on Sun. Can't wait.
|
A guy in the local miata club has an M45 that makes about 150whp so yeah that sounds right.
|
Originally Posted by mwest
(Post 545842)
I've opted to replace my 1.6 M45 set up for a 1.8 bored out to 2.1, balanced and blue printed. With a 99 head and new header plus other accessories, expecting to get about 170rwhp, naturally aspirated. This should give me much fewer hassles on the track. Will be starting the swap mid-June. Plan is to get more power with less agg. More time on the track less time under the car.
That would require a 4mm overbore... |
All times are GMT -4. The time now is 09:01 AM. |
© 2024 MH Sub I, LLC dba Internet Brands