Clutch and rear main replacing this weekend, any tips, do's and don'ts????
#1
Clutch and rear main replacing this weekend, any tips, do's and don'ts????
Got a very leaky rear main, might as ewell do the clutch while I'm at it this weekends project. Any real tips, do's or don'ts that I should be aware of. I've done old musclecar clutches before years ago, but it has been a while.
Also, what is the secret to getting the console to pop out to get the shift boot off. The rear main is a pressin type seal, what would be the way of removing it without damaging the crank surface. Thansk again for the help.
Also, what is the secret to getting the console to pop out to get the shift boot off. The rear main is a pressin type seal, what would be the way of removing it without damaging the crank surface. Thansk again for the help.
#2
The console is held in by 4 or 5 screws I believe 2 on the sides by the shifter and 2 or 3 under the lid, just undo those and it should lift right up. As for the seal I used this just because I alreday had one I'm sure there is another way
http://www.sears.com/shc/s/p_10153_1...=SPM6169885002
Oh yeah and if the motor is in the car lots and lots of extensions
http://www.sears.com/shc/s/p_10153_1...=SPM6169885002
Oh yeah and if the motor is in the car lots and lots of extensions
#3
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
Tools that you need to make the job easy.
3 foot extension
wobble joints
HF transmission jack
seal puller
Before you remove the transmission put a jack on the front of the oil pan. This way when you remove the transmission the engine does not rock forward. It makes putting the transmission back in a lit easier. Soak all the header bolts and transmission bolts in pb blaster starting a few days in advance. Other then that it is pretty easy.
3 foot extension
wobble joints
HF transmission jack
seal puller
Before you remove the transmission put a jack on the front of the oil pan. This way when you remove the transmission the engine does not rock forward. It makes putting the transmission back in a lit easier. Soak all the header bolts and transmission bolts in pb blaster starting a few days in advance. Other then that it is pretty easy.
#4
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,209
Total Cats: 1,139
Don't forget to resurface the flywheel.
For the seal, remove the transmission. If you have a hoist and the space, a few of us will recomend you remove the engine and transmission as one, then take the transmission off for the clutch and rear main seal. If you have a lift and/or tranny jack, just remove the transmission. Follow the Hayne's manual, it's fairly helpful. The rear main seal is part of a bracket. Remove the bracket with 4 m8 bolts, replace the seal on your workbench, then reinstall the bracket. You can use a piece of 2x4 to press the seal in straight.
http://www.miata.net/garage/clutch/index.html
For the console, it's just a bunch of screws. Two in the front on either side, one underneath the cup holders, two in the storage compartment. Then it'll pop off, don't forget the wiring clip for the power windows, which is there for non PW too. See page 12
http://www.miata.net/garage/DashRmv_89_93.pdf
Good time to rebuild your shifter too.
http://clubroadster.net/vb_forum/showthread.php?t=21545
Don't forget to resurface the flywheel.
m.net garage is your friend.
For the seal, remove the transmission. If you have a hoist and the space, a few of us will recomend you remove the engine and transmission as one, then take the transmission off for the clutch and rear main seal. If you have a lift and/or tranny jack, just remove the transmission. Follow the Hayne's manual, it's fairly helpful. The rear main seal is part of a bracket. Remove the bracket with 4 m8 bolts, replace the seal on your workbench, then reinstall the bracket. You can use a piece of 2x4 to press the seal in straight.
http://www.miata.net/garage/clutch/index.html
For the console, it's just a bunch of screws. Two in the front on either side, one underneath the cup holders, two in the storage compartment. Then it'll pop off, don't forget the wiring clip for the power windows, which is there for non PW too. See page 12
http://www.miata.net/garage/DashRmv_89_93.pdf
Good time to rebuild your shifter too.
http://clubroadster.net/vb_forum/showthread.php?t=21545
Don't forget to resurface the flywheel.
m.net garage is your friend.
#8
One tip I can think of is to leave the tranny in gear. That way when you go to put the tranny back up it will be harder to rotate the input shaft and allow you to twist the tranny to get the clutch splines to line up. Also make sure you have the correct clutch pilot tool. There are a few seals in the front of the tranny you should replace as well. No sense in pulling the tranny and not replacing them. Put a LIGHT COAT of grease on the tranny input shaft, this will help the splines slide into place on the clutch disc.
Second on getting the flywheel resurfaced, call around now and get prices and timelines from machine shops. Around here most machine shops charge $50 to resurface them and it takes at least a day. Autozone has 1.6 flywheels for $59, so you might want to just get one from there, but they are special order, so order it now to make sure you have it by the weekend.
http://www.autozone.com/autozone/par.../N-iwtstZ6o2oa
Plus one on the universal joint in 1/2" size. Another thing to note is that the power-plant frame is a bear to remove. There is a "pin" at the rear which locks the power-plant frame to the diff. it looks like a thick washer, with flat spots so you can pry it out.
Second on getting the flywheel resurfaced, call around now and get prices and timelines from machine shops. Around here most machine shops charge $50 to resurface them and it takes at least a day. Autozone has 1.6 flywheels for $59, so you might want to just get one from there, but they are special order, so order it now to make sure you have it by the weekend.
http://www.autozone.com/autozone/par.../N-iwtstZ6o2oa
Plus one on the universal joint in 1/2" size. Another thing to note is that the power-plant frame is a bear to remove. There is a "pin" at the rear which locks the power-plant frame to the diff. it looks like a thick washer, with flat spots so you can pry it out.
#9
Wow, all good info. Another thought is what clutch should I put in? The original has held so far, no problems, and I don't plan on going any higher than the 6psi I'm at now. Will a generic replacement clutch kit be ok or should I get something a bit better, if so, what? I don't have a tranny jack, how heavy is the trans, a one man job or should i get a friend under there with me. It looks like you can get to the two top bellhousing bolt from the engine compartment, is that a possiblity instead from below. Thanks for the help.
#11
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,209
Total Cats: 1,139
I'd go with FM's clutch. They spend a lot of time fine tuning the feel and apparently say it's great. You will also have their amazing customer service. It is also reasonably priced. Ebay clutch hold up for a budget, which is what I have. It's an on/off clutch though, so it's not suitable for street driving. Unless you hate yourself.
#14
I"m only running 6psi, intercooled, can't imagine any more than 150hp. The stock 1.6 clutch has held up so far. Car has been turboed for 40k miles. Although I'm not too hard on it. So The 1.8 stuff will fit totally, no issues at all. just bolt in and go. That seems too easy. A guy around here has a 1.8 OEM clutch and PP new in box, Auto zone has the flywheel. I'm good to go. Oh, by the way, the oil leak is Unfortunately NOT the rear main. It Is the turbo oil line off the block. Just couldn't see it. Darn! Oh well. 110k out of stock clutch its almost gone, so it all works out.
#15
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
While you're in there, you'll want to install a stainless clutch line. If you don't, you'll understand why you should have installed one when you're trying to get the curly-q to stay clear of the transmission as you lift it back up into the car.
#16
Senior Member
iTrader: (2)
Join Date: Sep 2009
Location: Edmonton, AB, Canada
Posts: 1,193
Total Cats: 29
If your taking the engine and tranny out as one do you need to remove the 2 rear Power Plant bolts? Last time I remember when putting in the urethane diff mounts those 2 long bolts that engage way up at the top would not move even with a supposed 600ft/lbs air gun. How do you get penetrating oil way up all in it back there? Though I'd rather just let them be if possible.
#20
Guys, I have an FM1 happy meal going in to my car in the next few days.
Would someone be able to name the seals that I should have the mechanic replace while we are in there..?
I would like to order them ahead of time to reduce the down time and how long the car is with them (chargeable time).
I think rear crank seal and someone above mentioned some gearbox ones..?
Would someone be able to name the seals that I should have the mechanic replace while we are in there..?
I would like to order them ahead of time to reduce the down time and how long the car is with them (chargeable time).
I think rear crank seal and someone above mentioned some gearbox ones..?
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM