Doing my suspension next week... any pointers?
#1
Senior Member
Thread Starter
iTrader: (2)
Join Date: Mar 2014
Location: Meridian, Mississippi
Posts: 628
Total Cats: 44
Doing my suspension next week... any pointers?
I have my Xida coil over suspension ready to go on the car, just need to remove the stock parts and install then new Xida's with the upper mount from my stock shock assemblies. Do I need a spring compressor to remove those upper mounts from the stock setup?
Any weirdness I need to look out for? I have done shocks on other cars, just wondering if there are any quirks to the Miata I should watch out for.
Later,
Keith
Any weirdness I need to look out for? I have done shocks on other cars, just wondering if there are any quirks to the Miata I should watch out for.
Later,
Keith
#8
I've removed the tophat from a bunch of stock springs and never used a spring compressor. I did borrow one from advance auto once, but it was pretty much useless. I always take the shock/spring out, then remove the nut. It's like an adult sized jack-in-the-box, a lot more buildup of drama and anticipation than actual explosion. I wouldn't stick my eyeball next to the nut when removing it or anything, but in my experience there doesn't seem to be much danger to it.
#9
I would at least leave the top hat in the car, undo the bolt at the top slowly and use a jack under the control arm to drop it slow. Probably what leafy was suggesting
Stock springs have inches of preload in them, taking a tophat to the face definitely won't feel good.
#10
Senior Member
Thread Starter
iTrader: (2)
Join Date: Mar 2014
Location: Meridian, Mississippi
Posts: 628
Total Cats: 44
So, leave the upper mounts in the car while removing the shock and spring, then remove the mounts to put them on the Xida's. From what I remember seeing the "how to" video on 949 website, with the collars towards the bottom of the shock there is zero pre-load on the Xida springs when you install the upper mount. I will study all the methods in the miata.net garage, thanks for the heads up on that!
Now, I have done spring and shock swaps before but this is my first adjustable setup. I am looking for a "mild" drop, not putting it into the weeds. So, should I run the collars up until the springs are slightly pre-loaded to get where I want to be... or where about should the collars be for initial installation?
Thanks,
Keith
Now, I have done spring and shock swaps before but this is my first adjustable setup. I am looking for a "mild" drop, not putting it into the weeds. So, should I run the collars up until the springs are slightly pre-loaded to get where I want to be... or where about should the collars be for initial installation?
Thanks,
Keith
#11
Long bolt method and non-removal of the tophats here. I was told I HAD to remove the tophats and you absolutely don't. That will save you some work right there.
I disassembled the springs in my hands. The springs are weak. Point it away and you will be fine.
I wrote all about it in one of my posts a long time ago. I'll see if I can find it.
I disassembled the springs in my hands. The springs are weak. Point it away and you will be fine.
I wrote all about it in one of my posts a long time ago. I'll see if I can find it.
#15
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,209
Total Cats: 1,139
FYI, if you don't have stock bushings, I'd suggest using the lower ball joint method. It unbolts and is much easier than the long bolt method, IF you have poly bushings to let the control arm drop away. If you're planning for an immediate alignment, you can loosen the lower control arm, but I'd just suggest the long bolt method if you don't have poly bushings.
#16
Senior Member
Thread Starter
iTrader: (2)
Join Date: Mar 2014
Location: Meridian, Mississippi
Posts: 628
Total Cats: 44
FYI, if you don't have stock bushings, I'd suggest using the lower ball joint method. It unbolts and is much easier than the long bolt method, IF you have poly bushings to let the control arm drop away. If you're planning for an immediate alignment, you can loosen the lower control arm, but I'd just suggest the long bolt method if you don't have poly bushings.
So, assuming I do the upper control arm bolt method on front and rear, do I need to then remove the top mounts to put them on the Xida's? The instructions on the 949 site don't show installing them with the top mount on the car as an option, and how tight the top nut goes seems to be a "visual" assessment of the tightness, tighten it "just until the grommet distorts a little bit" Can you see this grommet if you install the shocks with the top mount already in the car?
Keith
#17
The stock top hats install from the bottom, but are secured from the top in the trunk by two nuts. The shaft goes into the hollow hole of the top hats and is then secured up top.
That being said, just call Emilio and get him to tell you what to do. I have horrible clunking sounds from the stupid Vmaxxs I put in, so maybe my method isn't the right way to do it.
Do it once, do it right. Call Emilio.
That being said, just call Emilio and get him to tell you what to do. I have horrible clunking sounds from the stupid Vmaxxs I put in, so maybe my method isn't the right way to do it.
Do it once, do it right. Call Emilio.
#18
why are you leaving the top hats in the car? previous suggestion is saying to leave the top hat in the car until you release the spring. At that point you can remove the top hat and put it on the shock.
The nut on the shaft is usually locking, so torque requirements are low. I think the FSM has like 25-30 ft-lbs or something in that range for stock. If you realllly need torque requirements for the Xidas, you can call/e-mail 949. Its very low though, just check the deflection on the rubber bushing.
The nut on the shaft is usually locking, so torque requirements are low. I think the FSM has like 25-30 ft-lbs or something in that range for stock. If you realllly need torque requirements for the Xidas, you can call/e-mail 949. Its very low though, just check the deflection on the rubber bushing.
#19
You'll be pleasantly surprised how easy the suspension is to replace. This was one of the first "major" mechanical procedures I did when I began wrenching and it gave me zero problems. Apply anti-seize when you bolt the long bolt back up.
Next week I'll be able to help more after I've done my own