Track crew: GB feeler for 11.75" rotor bracket for Wilwood Dynalite calipers
#22
Elite Member
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
I already have a buyer lined up for my 11" M-Tuned Corrado front brake brackets
I am also wanting to know if they will work on the track over the 15x8 1st gen 6uls which is what I have now. If they do, and we can make this happen soon, say in the next month or two, I am in because I need to do something for the front.
The ultimate upgrade I lust for is the V8R kit but that is $2300 list. Right now the rears are doing fine on sport rotors and XP8s so I am not sure I 'need' the 4-corner upgrade.
I am also wanting to know if they will work on the track over the 15x8 1st gen 6uls which is what I have now. If they do, and we can make this happen soon, say in the next month or two, I am in because I need to do something for the front.
The ultimate upgrade I lust for is the V8R kit but that is $2300 list. Right now the rears are doing fine on sport rotors and XP8s so I am not sure I 'need' the 4-corner upgrade.
#25
What's the estimated weight difference with these verse the 11" Wilwood rotor? It sounds nice getting more rotor for cheap but if this is at the expense of too much unsprung weight gain it might not be worthwhile?
#26
Former Vendor
iTrader: (9)
Join Date: Jan 2008
Location: Bay Area, California
Posts: 929
Total Cats: 9
The replacement friction ring for the Wilwood 11" kit is 7.9 lbm and the replacement friction ring for the 11.75" in question is 8.1 lbm. I'm gonna go ahead and say you don't need to worry about the extra .2 lbm.
#27
Yeah, nice!
#28
Former Vendor
Thread Starter
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,099
Racing Brake lists the weight of a standard stock Corrado rotor at 12.72lbs. Wilwood lists the 11.75 outer rings at 8.1lbs and the hats at 1.6lbs. Assuming everyone's using fairly accurate scales, you'll shave ~3lbs per side going from 11" Corrado rotors to 11.75 Wilwoods.
#30
Senior Member
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
Then in post #2 I ask:
And in post #4 I acknowledge receipt of said information.
Seriously bro. Pay attention.
#32
Racing Brake lists the weight of a standard stock Corrado rotor at 12.72lbs. Wilwood lists the 11.75 outer rings at 8.1lbs and the hats at 1.6lbs. Assuming everyone's using fairly accurate scales, you'll shave ~3lbs per side going from 11" Corrado rotors to 11.75 Wilwoods.
#34
Read it yesterday, replied today. So sorry to offend you.
#35
Racing Brake lists the weight of a standard stock Corrado rotor at 12.72lbs. Wilwood lists the 11.75 outer rings at 8.1lbs and the hats at 1.6lbs. Assuming everyone's using fairly accurate scales, you'll shave ~3lbs per side going from 11" Corrado rotors to 11.75 Wilwoods.
stock 1.8 rotors weigh ~10lbs so looks like roughly even swap to 11.75 rings. w/ iron calipers/mounts replaced with alum. sounds like win.
#36
Hmm.. Tempted now. I've been holding off on piecing a brake setup together until next season but at ~1k that's a pretty damn good deal, especially when replacement rings are 30 bucks a pop.. Assuming you run this front setup, what would you gents recommend on the rear end to keep some semblance of brake balance? (1.8 non-sport stock rears)
#38
When I wear out my current 11" friction rings I may be interested in a set of your brackets if they are the right price and are anodised in hot pink.