Cspence's Build Thread
#23
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
eBay Motors: 3" 16 ga. mild steel mandrel bent tubes. (item 140303869569 end time Mar-01-09 20:18:47 PST)
#32
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
I would, but every exhaust is a little different....and I don't have the facilities to do so at the moment ( I had to call in some favors)
Will do....they're just small retangular hallogens that the kid who owned the car before me put in there. I'm going to retrofit in some HID projectors in there and make some plexiglass lenses to enclose the opening. Not a top priority but it will quickly become one the more I drive at night.
I would, but I dont think my company would feel the same way. They just don't share the passion....
It sounds pretty good, a little quiet at idle, but awsome driving. I want to swap out my cat now that I passed emissions. Plan on just putting in straight pipe and running the res and muffler.
Me too...except when I have the right equipment, I knew I get up everyday for work for a reason!
Thanks!
Ya $40 on ebay, you check out the link I posted? The seller was DawnMsn if your interested in picking up some.... As for the fan, I do only run a pusher but I never even have to turn it on. Drove it like 50 miles yesterday without it....then again it was only like 60 degrees out. The giant hole in front of the radiator helps a little, lol!
Thanks, I got extras....shoot me a pm
Thanks!
Thanks, I got extras....shoot me a pm
Last edited by Cspence; 04-16-2009 at 12:20 PM.
#35
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
Just made up a few more pieces that I had been meaning to get done. One to cover the hole that goes from the cowl to the cabin and then a temporary heat shield for the exhaust until I can make a permanent one (Used a piece of steel I had laying around which was'nt long enough to go along side of the turbo)...
0421091954.jpg?t=1240368669
0421091954b.jpg?t=1240368902
0421092014.jpg?t=1240368931
0421092025a.jpg?t=1240369209
0421092046.jpg?t=1240369282
0421092058.jpg?t=1240369400
DSC03321.jpg?t=1240448786
0421091954.jpg?t=1240368669
0421091954b.jpg?t=1240368902
0421092014.jpg?t=1240368931
0421092025a.jpg?t=1240369209
0421092046.jpg?t=1240369282
0421092058.jpg?t=1240369400
DSC03321.jpg?t=1240448786
Last edited by Cspence; 04-22-2009 at 09:08 PM.
#38
Elite Member
Thread Starter
iTrader: (11)
Join Date: Jun 2007
Location: Meriden, CT
Posts: 2,065
Total Cats: 1
Old:
DSC03342.jpg?t=1240449218
New:
DSC03343.jpg?t=1240449257
Old:
DSC03339.jpg?t=1240449435
New:
DSC03331.jpg?t=1240449529
DSC03337.jpg?t=1240450390
DSC03338.jpg?t=1240450332
Old:
DSC03340.jpg?t=1240449298
New:
DSC03334.jpg?t=1240449373
DSC03336.jpg?t=1240449406
Last edited by Cspence; 04-22-2009 at 09:37 PM.
#40
Elite Member
iTrader: (11)
Join Date: Jun 2007
Location: Overland Park, Kansas
Posts: 5,360
Total Cats: 43
Dude.. You're the man with sheet metal!!
Suggestion for next project!!!
Make something like that and sell em for 100$ a pop.. you'll make a KILLING!!! I would personally be interested in maybe looking into multiple pieces to cover the entire under carriage..
Suggestion for next project!!!
Make something like that and sell em for 100$ a pop.. you'll make a KILLING!!! I would personally be interested in maybe looking into multiple pieces to cover the entire under carriage..