Aidan's loose oily bunghole actually runs a track lap
#6283
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Made a to-do list and its long. So I knocked a couple small things off.
-R-pckg tie rod ends installed
-slim hub almost installed. Need to rewire the horn button the opposite way.
Thanks Stefan, its a significantly better driving position.
-R-pckg tie rod ends installed
-slim hub almost installed. Need to rewire the horn button the opposite way.
Thanks Stefan, its a significantly better driving position.
Last edited by aidandj; 02-15-2016 at 10:41 AM.
#6284
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Part of all the ms wiring i did today. I'm missing a bunch of 2.49k resistors but everything else is wired up.
Never build your MS with the ECU connector in the case. It sucks dick.
#6285
Elite Member
iTrader: (3)
Join Date: Apr 2014
Location: Huntington, Indiana
Posts: 2,885
Total Cats: 616
Yep, I want them, and the sensors. They'll look good sitting under the workbench in my garage next to the ABS axles. ****, ive even got an NB ABS booster and master already sitting in there too. So who's gonna sell me what?
I've also got one of the front spindles/sensor/hubs off Eds MSM, I'd be nice to complete that set as well.
I've also got one of the front spindles/sensor/hubs off Eds MSM, I'd be nice to complete that set as well.
If we can trade uprights, I would be fine with that.
Just give me a few days to pull, as it is bitterly cold here, and I'm working 100+ hr weeks until the end of the month.
I also have front spindles, but they're rough.
$60 shipped?
#6289
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I'm looking for a good communicator, for an in car setup. Similar to an aviation headset or something. Does anyone know of a 2 way communicator system that isn't ridiculously expensive?
#6290
If outside a helmet, you will want something with a hyper cardioid picup patern and a responce shaped for human voice. I know hams have a prefered crystal mic like this but can't remeber what it is off the top of my head.
#6291
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
This is specifically for outside a helmet. What would you suggest for the audio part?
I'm going to keep searching for cheap headsets on cl and stuff, but ideally it would use the same connection as a radio headset, but just be wired between the 2.
I'm going to keep searching for cheap headsets on cl and stuff, but ideally it would use the same connection as a radio headset, but just be wired between the 2.
#6292
Yeah, headsets can be found. I have a nice Bayredynamic DT108 headset/mic I got for $30 at a ham-fest that would be perfect for something lime this. Maybe some army surplus of some sort might work?
#6293
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Push to talk doesn't really matter to me. More for me and a passenger (read hailey) on long trips.
Found a couple decent ones on local CL, will keep searching. I'll check out my local army surplus too.
I'll give you $35 for it
Oh and I specifically want the noise canceling ones.
Found a couple decent ones on local CL, will keep searching. I'll check out my local army surplus too.
I'll give you $35 for it
Oh and I specifically want the noise canceling ones.
#6294
PTT is handy if the mics pick up a lot of car noise (will have to test and see).
If you want to be real fancy, you could add a line in for music and even an out to connect the mics to a phone through one of those TRRS connectors.
this is where just about every audio circuit I have built has been stolen from.