Aidan's loose oily bunghole actually runs a track lap
#6263
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
I got it for cheap. And I got the 01+ for cheap. So I will sell it for cheap. Sean might want it too, but both of you are just going to put it in your garage and not use it.
Need to figure out all the extra parts I acquired while buying abs **** on ebay.
Need to figure out all the extra parts I acquired while buying abs **** on ebay.
#6267
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Turns out josh didn't have the bracket either. So after staring at Mobius' all morning, I didn't have a bracket to do ABS plumbing. So I plumed the line lock and new master cylinder instead.
Speaking of @Mobius check out his shock
Currently on the hunt for a spring isolator that works with gen2 xidas. May have to resort to custom making one.
Speaking of @Mobius check out his shock
Currently on the hunt for a spring isolator that works with gen2 xidas. May have to resort to custom making one.
#6268
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
@Leafy, @codrus
ABS swap questions
-I don't have any of the 3 fuses in the upper left side. ABS, Fusible link, or stop fuse.
Can I just run fuse holders from the fuse box always hot wire?
-No idea if I have the fuses in the upper right, I have a 90, so I'm guessing I don't. Is there a good place to tap those connections off of?
-I have the brake indicator, just need to figure out which pin it is on in the gauge cluster.
-Don't have an ABS light. Was thinking about just adding an LED+Resistor and sticking it somewhere up by the dash. Or just repurpose my airbag light?
-Wheel speed sensors are simple. Just run lots of wires everywhere.
-What are the 2 in the bottom left. One is a ground? Can I just run that to any old chassis ground? And I can't tell what the one on the far bottom left is.
ABS swap questions
-I don't have any of the 3 fuses in the upper left side. ABS, Fusible link, or stop fuse.
Can I just run fuse holders from the fuse box always hot wire?
-No idea if I have the fuses in the upper right, I have a 90, so I'm guessing I don't. Is there a good place to tap those connections off of?
-I have the brake indicator, just need to figure out which pin it is on in the gauge cluster.
-Don't have an ABS light. Was thinking about just adding an LED+Resistor and sticking it somewhere up by the dash. Or just repurpose my airbag light?
-Wheel speed sensors are simple. Just run lots of wires everywhere.
-What are the 2 in the bottom left. One is a ground? Can I just run that to any old chassis ground? And I can't tell what the one on the far bottom left is.
#6271
So there are 3 power inputs, 10A for the ABS computer, 20A for the solenoid, and "fusible link" for the pump. The ABS computer is supposed to be hot-in-start-and-run but if you give it hot-in-run-but-not-start then all that happens is that the ABS unit resets when you start the car and takes 3-4 seconds to come back to operating condition. Not really a big deal.
So yeah, piggyback the computer off some other existing fuse (it doesn't draw anything like 10A, it's just fused at that level), and run new fuses for the solenoid and the pump. I use a 50A fuse for the "fusible link" replacement.
(BTW, "stop fuse" is just the brake lights -- I hope you have a fuse for that!)
The two bottom lefts are both grounds, I grounded it on the chassis near the bracket.
I recommend putting a switch on the power line to the ABS computer so that you can shut it off easily. Run the two diag connector wires somewhere easy to get to so that you can ground them in order to trigger the diag mode so you can clear the codes.
--Ian
So yeah, piggyback the computer off some other existing fuse (it doesn't draw anything like 10A, it's just fused at that level), and run new fuses for the solenoid and the pump. I use a 50A fuse for the "fusible link" replacement.
(BTW, "stop fuse" is just the brake lights -- I hope you have a fuse for that!)
The two bottom lefts are both grounds, I grounded it on the chassis near the bracket.
I recommend putting a switch on the power line to the ABS computer so that you can shut it off easily. Run the two diag connector wires somewhere easy to get to so that you can ground them in order to trigger the diag mode so you can clear the codes.
--Ian
#6276
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,441
Total Cats: 1,899
Yep, I want them, and the sensors. They'll look good sitting under the workbench in my garage next to the ABS axles. ****, ive even got an NB ABS booster and master already sitting in there too. So who's gonna sell me what?
I've also got one of the front spindles/sensor/hubs off Eds MSM, I'd be nice to complete that set as well.
I've also got one of the front spindles/sensor/hubs off Eds MSM, I'd be nice to complete that set as well.
#6279
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
No worries. Josh had one locally.
I'll get it all written up when I can. You will need a VR conditioner, and some spare ms3 inputs, I'm using pt4 and pt5
I'll get it all written up when I can. You will need a VR conditioner, and some spare ms3 inputs, I'm using pt4 and pt5