My '91 Turbo track build - GeneSplicer
#363
Elite Member
Thread Starter
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
Could also be from a shitty laser alignment - it's in my plans to get Iron Canyon's alignment kit to do my own alignment. I did find the jam nut backed all the way out from my drivers rack joint, which could have allowed more toe +/-
Soon as I can, I'll check alignment... but come in the fall, it'll be a diffferent car. Will keep updates posted!
Soon as I can, I'll check alignment... but come in the fall, it'll be a diffferent car. Will keep updates posted!
#367
Elite Member
Thread Starter
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
my try at drifting around T5 - yeah, I FAIL... slow clumsy hands - even hit the mirror trying to hold it. I need one of them tractor steering wheel ***** -or let go of the wheel more.
#370
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,192
Total Cats: 1,136
You suck cause you're trying to hand over fist control it. Just open your hands and let the wheel spin. Grab the wheel when it reaches a little bit of an angle, probably half the steering's rotations. This does it for me every time. It goes too fast for me to keep up.
#371
Elite Member
Thread Starter
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
lol Mark - I let Sandro go b/c I just got out on track, want to warm things up a bit - he had NOTHING special in it.
My sideways action through 5 was induced by a failed rev match into 2nd with a lot of rear bias in a heavy brake zone - the vette creeping up might have also played into the equation But yeah, I really need to let go of the wheel more like I mentioned above... I have this control problem you see, I don't have any!
My sideways action through 5 was induced by a failed rev match into 2nd with a lot of rear bias in a heavy brake zone - the vette creeping up might have also played into the equation But yeah, I really need to let go of the wheel more like I mentioned above... I have this control problem you see, I don't have any!
#373
Elite Member
Thread Starter
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
Not with a blown HG! Next time you see me I'll be rocking the 1.8 AF setup, but that may take months with new ecu and clutch to order and install, not to mention finishing the forged 1.8
#375
Elite Member
Thread Starter
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
Here's that vid just for Collin... no turbo fur you!
And, most of you might notice that minty-green turbo of Nickt93... he happily hooked me up with that Begi IC and Synapse valve for the track car - which after this weekend, REALLY wish I had ready. This course screams miata!
And, most of you might notice that minty-green turbo of Nickt93... he happily hooked me up with that Begi IC and Synapse valve for the track car - which after this weekend, REALLY wish I had ready. This course screams miata!
Last edited by GeneSplicer; 06-17-2012 at 08:54 PM.
#378
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
Just FYI Nasa is having an event at AMP in October. I and Gryff are planning on going. You all should come out also. We all need to enter the halloween costume contest as Gay hair stylist spec miata drivers.