A baffle necessary?
#1
Elite Member
Thread Starter
iTrader: (6)
Join Date: Sep 2007
Location: CA
Posts: 2,016
Total Cats: 13
A baffle necessary?
1) Would it cause alot of turbulence if I didn't use the baffle? My DP is just a single 2.5" tube, no divorcing.
I am going EWG so the flapper will be closed.
2) Any way to close the flapper w/ out welding it shut?
I am going EWG so the flapper will be closed.
2) Any way to close the flapper w/ out welding it shut?
#2
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,052
Total Cats: 6,615
I fail at fluid dynamics, so I won't pretend to give an answer here. However,
Easy. Use a piece of threaded rod or similar, with a clevis-type end, with to draw the wastegate arm shut, just like the canister would in the normal configuration.
2) Any way to close the flapper w/ out welding it shut?
#4
I would say use it. Cause the baffle is there to hold fluid in place for the suction/supply line to draw from. *Depending on how you drive, drift, drag and what not the fluid would be shifting all over the reservoir and if it sucked up some air that could be bad. Then you could run into fluid lock and all other kind of problems.
#5
I would say use it. Cause the baffle is there to hold fluid in place for the suction/supply line to draw from. *Depending on how you drive, drift, drag and what not the fluid would be shifting all over the reservoir and if it sucked up some air that could be bad. Then you could run into fluid lock and all other kind of problems.
I could be mistaken but I think the OP is referring to the baffle in some downpipes that keeps the wastegate flow from disrupting the exhaust flow... no fluid involved.
I'd venture that if you have the internal WG permanently shut then the baffle isn't particularly needed.
#7
I could be mistaken but I think the OP is referring to the baffle in some downpipes that keeps the wastegate flow from disrupting the exhaust flow... no fluid involved.
I'd venture that if you have the internal WG permanently shut then the baffle isn't particularly needed.
I'd venture that if you have the internal WG permanently shut then the baffle isn't particularly needed.
#8
Sounds like you've already gone to an external wastegate...so why not reap the full benefits.
Fluid flow at the turbine exit is very important...there is a reason the Tial exhaust housing have the hyperbolic curve on them. Even if you keep the flapper shut you are still leaving an eddy chamber next to your turbine. For what it would take to fab a baffle and weld it to the downpipe flange I would think it would be worth it.
Fluid flow at the turbine exit is very important...there is a reason the Tial exhaust housing have the hyperbolic curve on them. Even if you keep the flapper shut you are still leaving an eddy chamber next to your turbine. For what it would take to fab a baffle and weld it to the downpipe flange I would think it would be worth it.
#13
I could be mistaken but I think the OP is referring to the baffle in some downpipes that keeps the wastegate flow from disrupting the exhaust flow... no fluid involved.
I'd venture that if you have the internal WG permanently shut then the baffle isn't particularly needed.
I'd venture that if you have the internal WG permanently shut then the baffle isn't particularly needed.
Glass is a liquid. lol Sorry I didnt read his whole post, I just read the guy below his question. So I just answered the best I could.
I work with hydraulics so I just saw baffle and spouted out an answer. haha
#14
I thought this myth was recently busted? And not by the show...
Glass is a crystalline solid structure.
A prof of mine said they found that cathedral glass is thicker at the bottom due to the setting process, and not due to fluid flow over long periods of time.
Found a link:
Is glass liquid or solid?
Glass is a crystalline solid structure.
A prof of mine said they found that cathedral glass is thicker at the bottom due to the setting process, and not due to fluid flow over long periods of time.
Found a link:
Is glass liquid or solid?
Thread
Thread Starter
Forum
Replies
Last Post