Sintered steel oil pump gears
#47
Well if we know the metal and the hardness at different depths, and pictures if you got em onces its sliced we should be able to get a good idea of whats happening.
Personally, i dont care what they did to the original gear, i care what the gear ended up being.
Actually Im wrong. A carbon content would be nice, but we should be able to piece it together with some pictures and hardness tests
Personally, i dont care what they did to the original gear, i care what the gear ended up being.
Actually Im wrong. A carbon content would be nice, but we should be able to piece it together with some pictures and hardness tests
#49
Supporting Vendor
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
That's cool. Maybe we can get stealth97's old oil pump gears. I think I'm closer to his car than he is, so I can hold hostages.
If you've seen my dyno run vid on youtube, his car is in front of mine, right side.
If you've seen my dyno run vid on youtube, his car is in front of mine, right side.
#50
Not sure exactly what information they can provide. I do know they can do brinell hardness tests. Which would be possible on the outside of the gear and the inside. Not sure what the recommended method for cutting the gear would be though i'm sure they would know. I'm in metallurgy right now, only reason i know we have these labs. Hell we also have an SEM machine, electron microscopes are badass, tell you what.
They can also etch part of the piece and test the hardness of individual grains. Judging by the hardness of the inside and outside, i bet they would be able to tell what the base metal is as well as the heat treatment. Should be pretty simple stuff for the most part.
They can also etch part of the piece and test the hardness of individual grains. Judging by the hardness of the inside and outside, i bet they would be able to tell what the base metal is as well as the heat treatment. Should be pretty simple stuff for the most part.
#57
I just need a hand getting the timing gear off. the whole crank with OP attached is laying on my floor. Even after torch work, and taking three chunks out of it with my prybar, I only got it to move just enough to pull the crank out. If anyone wants it for testing youre welcome to it.
#59
oil pump failure...
FYI - this is what the powerlist had to offer about oil pump failures (in 2005) ...
>
Out of the 469 PowerList members (and I would presume the highest per capita number of built motors in all of Miatadom) only 4 built motors have gone south. And all four were oil pump failures. And all four were using the OEM oil pump. And all four were far exceeding OEM design redline of 7,200rpms.
So, morale of the story may simply be: Don't over rev. the BP.
I ask the question originally to gauge the collective wisdom on how much boost a built motor can safely see. It sounds like RPMs (and oil pumps) should be more of a concern. Does anyone know of BP over-boost failure?
Jim in Tucson
#1
I destroyed 3 built engines. In all cases the Oil Pump shattered and smoked the
crank and bearings.. Never lost one due to boost, or tuning (I tune my own
engines and take a great deal of time) My highest hp was 489hp and that was
with Turbo and Nitrous on that motor. I hope to crack 500hp with my newest
engine revision. 9000rpm? I found that 8100rpm was the breaking point..
7800-8000 and I never broke one..
Marc
#2
my highest powered NA was 170 RWHP with a 8500 redline failed due to a
failed oil pump.
Greg
>
Out of the 469 PowerList members (and I would presume the highest per capita number of built motors in all of Miatadom) only 4 built motors have gone south. And all four were oil pump failures. And all four were using the OEM oil pump. And all four were far exceeding OEM design redline of 7,200rpms.
So, morale of the story may simply be: Don't over rev. the BP.
I ask the question originally to gauge the collective wisdom on how much boost a built motor can safely see. It sounds like RPMs (and oil pumps) should be more of a concern. Does anyone know of BP over-boost failure?
Jim in Tucson
#1
I destroyed 3 built engines. In all cases the Oil Pump shattered and smoked the
crank and bearings.. Never lost one due to boost, or tuning (I tune my own
engines and take a great deal of time) My highest hp was 489hp and that was
with Turbo and Nitrous on that motor. I hope to crack 500hp with my newest
engine revision. 9000rpm? I found that 8100rpm was the breaking point..
7800-8000 and I never broke one..
Marc
#2
my highest powered NA was 170 RWHP with a 8500 redline failed due to a
failed oil pump.
Greg