Help me fix my subaru suspension
#1
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Help me fix my subaru suspension
OK I was doin my suspension with soviet tonight.
We did 3 corners no problem.
Fourth corner fail.
In short, we can not bolt in the upper bottom bolt on the shock body because the knuckle / brake disc thing won't go past the angle in the pic below. We tried jacking it, prying it etc but it wont budge.
Do you think the axle has popped out?
And if so, how do you pop it back in?
We did 3 corners no problem.
Fourth corner fail.
In short, we can not bolt in the upper bottom bolt on the shock body because the knuckle / brake disc thing won't go past the angle in the pic below. We tried jacking it, prying it etc but it wont budge.
Do you think the axle has popped out?
And if so, how do you pop it back in?
#4
the axles are different on left vs right sides. right side was cake, left side - impossible. i'm guessing one axle is slightly longer or something.
that car is the destroyer of tools. I cracked a 19mm socket (literally, has a 2cm crack in it now) and then we broke a 3/8" ratchet each.
I thought McPherson struts were easy??
that car is the destroyer of tools. I cracked a 19mm socket (literally, has a 2cm crack in it now) and then we broke a 3/8" ratchet each.
I thought McPherson struts were easy??
#7
the axles are different on left vs right sides. right side was cake, left side - impossible. i'm guessing one axle is slightly longer or something.
that car is the destroyer of tools. I cracked a 19mm socket (literally, has a 2cm crack in it now) and then we broke a 3/8" ratchet each.
I thought McPherson struts were easy??
that car is the destroyer of tools. I cracked a 19mm socket (literally, has a 2cm crack in it now) and then we broke a 3/8" ratchet each.
I thought McPherson struts were easy??
Oh, and buy some better tools children. Craftsman is not the same as Snap-on.
EDIT: For reattaching the axle, assuming it came out, just get the boot out of the way and actually watch the piece slide in. Much easier, IMO, than hoping it finds its' way into the right spot. Please for the love of god do not start cutting wheel wells.
#9
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Struts are a bitch 100% of the time. Why not just remove the arm, bolt the shock in, thread the springs all the way down, and reattach the arm by compressing the damper with a jack until the arm can be lined up with the sub-frame. I run into the same problem at work all the time. Everyone else is all "lets circle-jerk around it with a prybar for 5 hours"; whereas I pull the fuucking arm off and slide that ---- in. Problem solved.
Oh, and buy some better tools children. Craftsman is not the same as Snap-on.
EDIT: For reattaching the axle, assuming it came out, just get the boot out of the way and actually watch the piece slide in. Much easier, IMO, than hoping it finds its' way into the right spot. Please for the love of god do not start cutting wheel wells.
Oh, and buy some better tools children. Craftsman is not the same as Snap-on.
EDIT: For reattaching the axle, assuming it came out, just get the boot out of the way and actually watch the piece slide in. Much easier, IMO, than hoping it finds its' way into the right spot. Please for the love of god do not start cutting wheel wells.
Also, I am upgrading to harbor freight.
#10
on sunday I was supposed to come over to Fae's house with his tranny jack and install his new trans. however, my car decided it would be a cool idea to run on 2 cylinders instead so I ripped out half the wiring harness.
so he decide to come by on monday (for the jack) and do the subaru suspension because "it would only take 2 hours".
#11
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,178
Total Cats: 1,681
lol
on sunday I was supposed to come over to Fae's house with his tranny jack and install his new trans. however, my car decided it would be a cool idea to run on 2 cylinders instead so I ripped out half the wiring harness.
so he decide to come by on monday (for the jack) and do the subaru suspension because "it would only take 2 hours".
on sunday I was supposed to come over to Fae's house with his tranny jack and install his new trans. however, my car decided it would be a cool idea to run on 2 cylinders instead so I ripped out half the wiring harness.
so he decide to come by on monday (for the jack) and do the subaru suspension because "it would only take 2 hours".
#14
No, you would not need to disconnect the ball-joint. The articulation of the tie rod would allow for movement. Your main issue is; limited movement of the lower suspension arm, which prevents the knuckle from lining up with the lower shock mounting point. As 18psi suggested, your axle may have moved out of place. If it were my car, I would, remove lower control arm (via the 2 bolts which hold the arm on), re-align the axle, line up the knuckle with the lower shock mounting holes, and attach the bolts. At this point, lower the spring perch to allow the spring to drop. Slide the axle into the housing of the hub, and try to re-align the lower control arm. If you need more room to move the arm, use a jack to compress the damper, by applying force through the arm. With a little wiggling, it will fit.
This may not be the simplest, lowest-effort method; but it's slow, methodical, and the way I prefer to do things. Sometime doing more work actually makes the job easier. Don't forget to get it aligned afterwards.
FWIW: Pittsburgh are actually decent tools, the weak point is the ratchet gears. Over time they have trouble catching. The teeth don't fail, but it forces you to have a shorter; less efficient swing.
#18
Figured I'd reply to this thread since fae is still b& until his car runs
He came over to my house. Wiggled the knuckle while twisting the axle and the CV joint popped back in. Took all of 5 minutes.
The Forester hauls ***. Not a 300whp hauls *** but still a ton of fun. He drives it hard, too.
edit: MT advice was best. NASIOC wasn't helpful at all. Just goes to show how boss this forum is.
He came over to my house. Wiggled the knuckle while twisting the axle and the CV joint popped back in. Took all of 5 minutes.
The Forester hauls ***. Not a 300whp hauls *** but still a ton of fun. He drives it hard, too.
edit: MT advice was best. NASIOC wasn't helpful at all. Just goes to show how boss this forum is.