typicall newb ms2 only one coil is firing help please
#21
I wonder why....me think red line was the cam position sensor. can u explain to me what im looking at when i look at that light blue and red line?
its not supposed to be going to ground its supposed to go to one end of a 100ohm resistor for my ebc. not at home to verify but im pretty sure i diddnt make a mistake there...even though the pic looks like it goes straight into ground. ill check my wiring there too.
i diddnt know what to do i panicked...i figured since they were both for a similar motor and they both were for tunerstudio i diddnt think it mattered i just started looking for random maps to get the car started :(
how far off track am i????
its not supposed to be going to ground its supposed to go to one end of a 100ohm resistor for my ebc. not at home to verify but im pretty sure i diddnt make a mistake there...even though the pic looks like it goes straight into ground. ill check my wiring there too.
i diddnt know what to do i panicked...i figured since they were both for a similar motor and they both were for tunerstudio i diddnt think it mattered i just started looking for random maps to get the car started :(
how far off track am i????
#22
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,493
Total Cats: 4,080
you're missing the Green line above the blue which is the cam. blue is crank, and red is the error. where the spikes are where it's not seeing something it expects.
use the DIYPNP basemap. that could be an issue trying to load a msI map. http://www.diyautotune.com/diypnp/ap...93-16b6-mt.zip
use the DIYPNP basemap. that could be an issue trying to load a msI map. http://www.diyautotune.com/diypnp/ap...93-16b6-mt.zip
#25
ive established that im getting continuity between the coil trigger wires and ckp and cmp wires all the way back at the pcb.
idk what the problem is could be a bad cas but i actually bought a new BWD brand cas for a 97 miata with a brand spankin new pigtail from a alternator that just happen to plug right in.
ben from diyautotune says it wont start unless it gets a cam signal as well. how would i go about testing the cas does it directly output a fluctuating signal that i can connect to a cheap Chinese multimeter and confirm that it is functioning?
idk what the problem is could be a bad cas but i actually bought a new BWD brand cas for a 97 miata with a brand spankin new pigtail from a alternator that just happen to plug right in.
ben from diyautotune says it wont start unless it gets a cam signal as well. how would i go about testing the cas does it directly output a fluctuating signal that i can connect to a cheap Chinese multimeter and confirm that it is functioning?
Last edited by samwu8k; 10-27-2011 at 07:13 AM.
#32
not really sure how to hunt a short circuit down... i mean js10 is a hole. i have 2 wires going to it...neither of which are 12v. one goes to 5v trough a resistor and the other is just connected to the cas
hmm....i wonder what would happen if i play with that ****. u cant just pick ms2 so i think i just put something random as **** in. what should it be set to?
hmm....i wonder what would happen if i play with that ****. u cant just pick ms2 so i think i just put something random as **** in. what should it be set to?
#34
i switched coil a and b around unlike what was in the miata turbo wiki removed the s12c jumper wire....got a cam signal and this **** fired right up. im too FAWCKING HAPPY!!!!
on a side note my motherfucking clutch wont fully disengage fml...all is good tho this is just a minor mechanical issue!!!!!
THANKS EVERYONE!!!!
on a side note my motherfucking clutch wont fully disengage fml...all is good tho this is just a minor mechanical issue!!!!!
THANKS EVERYONE!!!!
Last edited by samwu8k; 11-04-2011 at 06:44 PM.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM