|
'95 Street/Track Build
28 Attachment(s)
I purchased the car in 2007 with the intentions of building it into a STS(2) car. I refreshed the motor because a leaking exhaust valve. For the next year in a half I spent some time trying to dial in the suspension and learn to drive on street tires. Just before the 2008 Solo Nationals I dynoed the car and found it was still down on power. A leak down test showed a leaky exhaust valve. A later tear down found a bent exhaust valve. I suspect the first machine shop did not properly check the valves like I asked the first time (it was the one thing I specifically asked them to check).
https://www.miataturbo.net/attachmen...ine=1341250428 https://www.miataturbo.net/attachmen...ine=1341250428 https://www.miataturbo.net/attachmen...ine=1341250428 Luckily a friend of mine was looking for a co-driver for his ASP prepared Corvette that year, so I took him up on the offer. After driving that car, I knew there was no going back to STS(2). I started researching a SSM build. While searching a another friend of mine offered me his 96 M edition with a FMII kit for one hell of a deal, so I took him up on it. https://www.miataturbo.net/attachmen...ine=1341250428 I swapped the motor from the '96 to my car (it was fresher and upgraded with Volvo valve springs). I put the '96 back to stock and sold it for almost as much as I bought it for. I ditched the Link from the '96 in favor of an AEM Series 1 EMS. Unfortunately the car set for over a year. Finally early last year I got the car back on the street. By this time I decided I was over auto-x (at least as nothing more than the casual participant) and figured I’d just have a fun street car I could do track days in (maybe NASA time trials). Custom radiator plate: https://www.miataturbo.net/attachmen...ine=1341250428 I purchased a roll bar and just enjoyed driving the car again. Then in haste to get home one day I pulled out and hit another car. Luckily it was low speed and only minor damage to the car. The corner was a little mangled, but I figured it was a good time for some upgrades! I got the corner straighten enough and took on Hustler as inspiration for my replacement fender. https://www.miataturbo.net/attachmen...ine=1341250428 To replace the bumper I am going with a VIS Racing, Racing Beat Type2 replica. http://i245.photobucket.com/albums/g...0615121745.jpg Attachment 185862 I am copying Savington’s RX7 oil cooler setup. The ’96 motor came with a oil filter relocation, so that part was going to be easy. I decided the web in the radiator support was a perfect place to run the lines and keep them short. Attachment 185863 https://www.miataturbo.net/attachmen...ine=1341250428 https://www.miataturbo.net/attachmen...ine=1341250428 Some McMaster-Carr (my favorite online store) clamps would keep everything neat and tidy. https://www.miataturbo.net/attachmen...ine=1341250428 https://www.miataturbo.net/attachmen...ine=1341250428 Upgraded the diff mounts: https://www.miataturbo.net/attachmen...ine=1341250428 Also going in is a CX Racing radiator and reroute. I found using a mirror made cleaning the old gasket off much easier, though it took awhile to learn how to use my hand looking into them mirror. It also helped that I had the diff out because I just jacked the PPF all the way up for more clearance. https://www.miataturbo.net/attachmen...ine=1341250428 The BEGi spacer required some work to make it clear my bell house. I had to tap the barb fitting deeper and trim the end to make it fit. https://www.miataturbo.net/attachmen...ine=1341250428 Still in the works for this summer: - Fan shroud - Polyurethane suspension bushings and reinstall refreshed Konis (not enough of a budget for REAL coilovers yet). - Revised intercooler plumbing (over radiator) - Ducting - Custom hood venting |
Looks good Andrew. I really like that oil cooler setup!
|
|
No problem. I really wanted some that looked factory. I just used a 1-1/4" hole saw to make two holes then cut in between them a Dremel cutoff disc. Unfortunately my Dremel died, so now I need to get a new one half way through the project, so the holes aren't as clean as I would like, but the silicon hose cut for edge trim hides it.
|
midten,
that routing does look really good! cant wait to see it done. |
1 Attachment(s)
Fresh coat of paint on the valve cover. A little Chevy engine orange to add a little color to the engine bay.
https://www.miataturbo.net/attachmen...ine=1341277524 |
2 Attachment(s)
Remounted the intercooler to be closer to the radiator:
https://www.miataturbo.net/attachmen...ine=1341887927 Finished up the cold side pipe. Going to move the BOV to the hot side: https://www.miataturbo.net/attachmen...ine=1341887927 |
Originally Posted by curly
(Post 898255)
---- me that's brilliant. I ran my lines above the support and through the big hole. Not nearly as neat as yours, and I have to put a bunch of tape on it to keep it sealed (ducting wise). Thanks for giving me a new project!
What did you do about a thermostat? Edit- I see it has an internal thermostat. WIN! |
I had no idea VIS knocked off the RBII front end. How is the quality, in your opinion?
|
Originally Posted by viperormiata
(Post 901267)
I had no idea VIS knocked off the RBII front end. How is the quality, in your opinion?
|
7 Attachment(s)
I got some more forward process this weekend. My friend finished up the hot side piping:
https://www.miataturbo.net/attachmen...ine=1342402563 While he worked on that, I cut the the hood to clear the new pipes. The cold side is pretty close to the hood, but it was a necessary evil because of the expansion area of the radiator. I only had a 4" angle grinder to work with. Once I get a working a Dremel, I'll clean up the cutouts to make them look a little better. https://www.miataturbo.net/attachmen...ine=1342402563 https://www.miataturbo.net/attachmen...ine=1342402563 https://www.miataturbo.net/attachmen...ine=1342402563 https://www.miataturbo.net/attachmen...ine=1342402563 https://www.miataturbo.net/attachmen...ine=1342402563 All closed up: https://www.miataturbo.net/attachmen...ine=1342402563 Hopefully this week I'll get my shroud done and the Spal fans installed. I got my Koni's back from Pro Parts USA and I'm going to work on the rest of the urethane bushings. |
Looking good man! Its come a long way since I saw it.
|
28 Attachment(s)
I've been busy getting the car back together.
I spent a few hours fussing with the bumper, brackets, fenders and hood to get everything lined up. Its not perfect, but given the fiberglass bumper and the crash tweaked some of the bumper mounts, I am pretty happy https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 Rebuilt Koni Yellow's (revalved too), my McMaster-Carr NB sway bar bolts, and adjustment hole on the RB 1.125" bar. https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 I have also been working on my ducting. The FMII intercooler posed a little bit of a problem. It hangs slightly lower than the radiator and its it is pushed as high as we can get it. So as you can see, I had to make a little window for it to sit in. I will cover the finished ducting with aluminum duct tape to keep any air from making its way out the window. Window layout: https://www.miataturbo.net/attachmen...ine=1345483462 1.25" hole saw for a cleaner cutout (same one I used for the oil lines) https://www.miataturbo.net/attachmen...ine=1345483462 Finished: https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 https://www.miataturbo.net/attachmen...ine=1345483462 I did have one small problem pop up. The FC oil cooler I bought had a crack in the thermostat housing (I think it was my fault for installing the thermostat backwards). So I had to pick up another oil cooler. Luckily this one doesn't leak. I've only driven it a few miles (without a bumper) but so far no leaks from the oil lines or the coolant reroute. I hope to get my radiator shroud done this week and then I'll finish up my ducting with some various bulb seals and sealing tape. In the mean time, I'll finish putting the bumper on tonight and enjoy the wonderful weather we are getting. https://www.miataturbo.net/attachmen...ine=1345483462 |
1 Attachment(s)
All wrapped up! Just one little seeping oil line fitting to clear up. The bumper took awhile to fit up, but it came out looking pretty good.
https://www.miataturbo.net/attachmen...ine=1345513270 |
Hey buy 2 6436K143 from mcmaster. for your swaybar and put them on the inside of the swaybar brackets to prevent the bar from walking. It is very un-fun when the bar walks in the middle of an ax run.
|
I used to have some, but I gave them to a friend who's CSP car I was driving a few years ago. They are on my list of parts for my next order.
|
7 Attachment(s)
Oh how I missed this car. The weather was great all week so I just left the hard top off an drove her work everyday this week.
Today I took some time to tighten up the oil cooler fitting that was seeping some. I also broke out some old rattle can painting skills from my drifting days (yes, I rocked a primer black AE86 hatch). Took some time today to paint the ducting and bumper support to clear up a few rust spots. https://www.miataturbo.net/attachmen...ine=1345935385 I modified the OEM splash guard to fit around my ducting. Complete with aluminum tape to seal it up (and keep it from flapping in the wind). https://www.miataturbo.net/attachmen...ine=1345935385 https://www.miataturbo.net/attachmen...ine=1345935385 A little aluminum tape to seal up window I had to cut for the intercooler end tank. https://www.miataturbo.net/attachmen...ine=1345935385 Finished the day off with a little white primer on the bumper and fender. This will have to do until I have time this winter to give it a full paint job. I decided to carry the black rocker stripe onto the front bumper to make it look at little cleaner. https://www.miataturbo.net/attachmen...ine=1345935385 https://www.miataturbo.net/attachmen...ine=1345935385 https://www.miataturbo.net/attachmen...ine=1345935385 |
That RB2 knock off looks great! So does all the work on the ducting and smart move by flipping the intercooler.
The whole car is completely tits. I like it. |
There were a few fitment issues, but I tweaked the fenders, headlight lids, and hood to get everything lined up. I know I'll have to pull it again at some point, so I didn't spend to long this time getting everything perfect.
My biggest complaint about it is the lack of holes. Some of them a easy to layout, but the ones from the bumper to the fender are a pain in the ass. They drilled the ones that hold the stud plate in place (but you can't use the plastic retainers because of the thickness of the fiberglass). So you have manually layout the holes and there is no real easy reference to take measurements from. I go them close enough and opened up the holes for adjustment. |
I took it out to a local auto-x to test out the rigidity of the front bumper. It took a few good solid cone hits with nothing but some scuffs in the primer. Halfway through the day, I decided to put my LG Lucid in the GPS mount and take some video
Run #4 Run #5 -- Fastest so far, but a coned it away. Run #6 -- Fastest time of the day |
| All times are GMT -4. The time now is 09:49 PM. |
© 2024 MH Sub I, LLC dba Internet Brands