Faelflora breaks his promise, time to part out car. GIT THE SAWZALL!
#1523
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
So my fuel pumps are working. THey flow enough fuel to uh flow a shitload of fuel. I primed them bitches and pumped like half a gallon in 3 seconds. Good enough.
Um I am waiting for my oil feed adapter. This bigass borg turbo takes a fruking 1/2" NPT adapter. After that, I think I will be ready to start it up.
Oh so I took a good look at my old manifold and exhaust today. The BEGI S5 mani is cracked at the welds between the cast iron and the wastegate area. The wastegate area is steel and I was told that's why it cracked. It wasn't leaking, but it needs to be repaired so I guess I will send it to BEGI. Into the void.
My enthuza exhaust hangers had broken off in two places. I had a big quarter sized hole where it ripped off on the midpipe thing, and another hole where it ripped off on the muffler. I blame that on having a downpipe with no flex section. No, one slip joint did not offer enough movement. AND I have to also mention that my vigorous flat shift fireballs and launch control fireballs etc may have had something to do with the destruction of my exhaust. Oh well. Everything dies someday.
These holes also explain why shuiend's identical enthuza exhaust was SIGNIFICANTLY quieter than mine.
Um I am waiting for my oil feed adapter. This bigass borg turbo takes a fruking 1/2" NPT adapter. After that, I think I will be ready to start it up.
Oh so I took a good look at my old manifold and exhaust today. The BEGI S5 mani is cracked at the welds between the cast iron and the wastegate area. The wastegate area is steel and I was told that's why it cracked. It wasn't leaking, but it needs to be repaired so I guess I will send it to BEGI. Into the void.
My enthuza exhaust hangers had broken off in two places. I had a big quarter sized hole where it ripped off on the midpipe thing, and another hole where it ripped off on the muffler. I blame that on having a downpipe with no flex section. No, one slip joint did not offer enough movement. AND I have to also mention that my vigorous flat shift fireballs and launch control fireballs etc may have had something to do with the destruction of my exhaust. Oh well. Everything dies someday.
These holes also explain why shuiend's identical enthuza exhaust was SIGNIFICANTLY quieter than mine.
#1524
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Oh BTW here are some pics of my 4" yes four inch exhaust. 3.5" Downpipe is big. This is huge.
Comes out at a nice jaunty ricery angle. I figure I should have enough "**** you" power to back up the ostentatiousness.
Comes out at a nice jaunty ricery angle. I figure I should have enough "**** you" power to back up the ostentatiousness.
#1526
Elite Member
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,905
Total Cats: 400
4" after a 3.5" downpipe doesn't make much sense to me, but whatev. Looks badass. What muffler are you running? I can see it's relatively tiny. I'm considering a 4" piece on my V6 build if I can find a big enough muffler and a 4" flex.
#1527
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Not much at all. I will take a head on pic later.
It's just some Invidia canister exhaust. It shouldn't rust at all, like the magnaflow "stainless" muffler did. I could fit my whole arm through the exhaust.
It's just some Invidia canister exhaust. It shouldn't rust at all, like the magnaflow "stainless" muffler did. I could fit my whole arm through the exhaust.