Faelflora breaks his promise, time to part out car. GIT THE SAWZALL!
#2521
So.
I have figured out a way to deal with my fuckye up drain.
I am gonna put a npt plug in the current hole which is about 6 inches back from the front
And then drill and tap pan at the standard spot teo inches from the back. Done.
Should have done this three months ago.
Current spot sucks too cus oil drain is only two inches long now.
I have figured out a way to deal with my fuckye up drain.
I am gonna put a npt plug in the current hole which is about 6 inches back from the front
And then drill and tap pan at the standard spot teo inches from the back. Done.
Should have done this three months ago.
Current spot sucks too cus oil drain is only two inches long now.
kthx <3
#2522
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
Weld it and forget it. Plus with the motor out you can change that oil pump that has forever scared me. Do they sell billet gear sets for the vvt pump? If so put that in because with the RPM you give it you will need it.
#2524
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
OK. The car will run again tomorrow.
I plugged the old fu(king hole. I do not think a welded bung there would help. Shamelessly, I will post a picture of the jb-welded, rtv'd-up old drain. It was just too short. Even with push-loc hose it would always exert pressure. I also don't believe in welded AN male fittings. Ideally, if there is room, you should weld on a female NPT fitting, and then screw in a male-male NPT-AN adapter. AN fittings strip out way too easily. It's slowly happening with my big -12 fittings FTL.
To plug the hole I just put in the plug with some jb weld. Done.
Now off to the store to get a 3/8 NPT tap and a gallon of mineral spirits. I lost my old BEGI kit tap :( Am going to tap in the standard place, with oil in the pan and grease on the bits. Will flush the pan a whole bunch through the hole. Will finish off with hand drill for the sized drill bit.
I plugged the old fu(king hole. I do not think a welded bung there would help. Shamelessly, I will post a picture of the jb-welded, rtv'd-up old drain. It was just too short. Even with push-loc hose it would always exert pressure. I also don't believe in welded AN male fittings. Ideally, if there is room, you should weld on a female NPT fitting, and then screw in a male-male NPT-AN adapter. AN fittings strip out way too easily. It's slowly happening with my big -12 fittings FTL.
To plug the hole I just put in the plug with some jb weld. Done.
Now off to the store to get a 3/8 NPT tap and a gallon of mineral spirits. I lost my old BEGI kit tap :( Am going to tap in the standard place, with oil in the pan and grease on the bits. Will flush the pan a whole bunch through the hole. Will finish off with hand drill for the sized drill bit.
#2529
I read through the whole thread over days. Here is a guy pouring tons of time and money into a project he is learning on and documenting the process in a stream of consciousness output.
I think most people have a few similar stories and definitely make different choices but his build isn't that far removed from most. He just seems to be brutally hones about his ruckus and process with little apparent care for showmanship, structure or organization. I'm guessing there is no build book, notes, spreadsheets, failure tracking etc and that it's all just held in memory.
I like it but like everyone would like to see dyno numbers. I can't believe the frantic work and changes just before each dyno day. It's like the process of validation prior to an extent is undesirable in Fae's world.
I think most people have a few similar stories and definitely make different choices but his build isn't that far removed from most. He just seems to be brutally hones about his ruckus and process with little apparent care for showmanship, structure or organization. I'm guessing there is no build book, notes, spreadsheets, failure tracking etc and that it's all just held in memory.
I like it but like everyone would like to see dyno numbers. I can't believe the frantic work and changes just before each dyno day. It's like the process of validation prior to an extent is undesirable in Fae's world.
#2531
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Note that i also needed to replace my alternator tensioner bolts. That was causing my belt to loosen up over time. By time i mean 30 miles. Sucked. Yes you can get the tensioner bolts and block from mazda. Dealer.
#2536
Elite Member
Thread Starter
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
I poured three gallons of mineral spirits through the hole and all over my garage floor. Hopefully I got all the shavings out. Then poired two quartd of crappy oil through.
Gonna make my hose outa push loc blue bbundy stuff. Hope to lay boost tomorow all over matts heathen pizza
Gonna make my hose outa push loc blue bbundy stuff. Hope to lay boost tomorow all over matts heathen pizza
#2538
Jesus man, can you do anything right? This is how you jb-weld ----:
https://picasaweb.google.com/1071657...eat=directlink
https://picasaweb.google.com/1071657...eat=directlink