|
Originally Posted by Savington
(Post 1432658)
Wheel width is bead to bead. Add another 10mm per side to get the full height dimension (so a 10" 254mm wheel measures 274mm tall when sitting on the ground). (10mm for at least the 6UL and Jongbloed Aero500, I measured both.) A 9" 6UL measures ~160mm from hub face to inner edge, less 10mm, less ~114mm (4.5"), gets you 36mm. 10" 6UL measures ~162mm from hub face to inner edge, less 10mm, less 127mm (5"), gets you 25mm.
I think you have +10s. @Savington Measurements taken with wheel sitting "face" down. Due to stancey stretch, measuring from floor is accurate as wheel is contacting floor. Total height: 280.5mm Backspace: 164mm Mounting pads (entire relief, didn't have a great way to just get the lug holes): 15.5mm What is going on? |
Based on those numbers, I get 23.75mm of offset.
|
Same here. I'm at a total loss, and i'm reasonably sure nobody put a custom 4-6" wider subframe front and rear in the car prior to my ownership.
|
Compared track (at lower "edge" of wheel) on the two cars in my garage.
Hater Front: 69.5" DD Front: 63" Hater Rear: 69.75" DD Rear: 63" |
What wheel does the DD have?
|
Stock NB1. It's a 99. Haven't measured camber, but it's got a good bit. It's slammered on Xidas.
|
how i feel trying to solve this issue
https://pbs.twimg.com/profile_images...Hh_400x400.jpg |
I'm betting you got some 10" +10 wheels. A "narrow" Maxxis 245 on an 11" would be like, exposing the bead stretched.
https://cimg4.ibsrv.net/gimg/www.mia...06607a417c.jpg |
Measurements are above. Does not appear to be +10s. The plot sickens.
|
Do you have ELBJs, maxed-out camber bolts, adjustable upper arms, and a pinchweld height of ~4" or lower?
|
Originally Posted by concealer404
(Post 1434286)
Measurements are above. Does not appear to be +10s. The plot sickens.
I don't have an unmounted 10 laying around right now, let me go pull one off Bullet... |
Originally Posted by Savington
(Post 1434288)
Do you have ELBJs, maxed-out camber bolts, adjustable upper arms, and a pinchweld height of ~4" or lower?
|
Originally Posted by Savington
(Post 1434288)
Do you have ELBJs, maxed-out camber bolts, adjustable upper arms, and a pinchweld height of ~4" or lower?
2) Very no 3) Yes (but not all weird and jacked up because of lack of camber bolt necessary to hit -3) 4) 4.25" |
Ahhhh, I should have been paying attention with you guys were aligning it.
|
Obviously, you have the extremely limited edition wide-track miata that Mazda produced in secret.
|
Originally Posted by concealer404
(Post 1434251)
Mounting pads (entire relief, didn't have a great way to just get the lug holes): 15.5mm
|
|
Originally Posted by TurboTim
(Post 1434352)
What is this measurement?
How many people find a total width of a little over 11" very strange for a 10" wheel? |
Wait a minute...
Originally Posted by concealer404
(Post 1434251)
Measurements taken with wheel sitting "face" down. Due to stancey stretch, measuring from floor is accurate as wheel is contacting floor. Total height: 280.5mm Backspace: 164mm |
Originally Posted by TurboTim
(Post 1434355)
Wait a minute...
So you have the outside of the wheel on the ground, and you're using a tape measure to measure the height of the wheel and the height of the mounting pad? In that case, these are -23.75's, not +23.75's. |
| All times are GMT -4. The time now is 10:51 AM. |
© 2026 MH Sub I, LLC dba Internet Brands