Jeff_Man racing Ver. 2.0
04-14-2010, 07:40 PM
#1
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
Jeff_Man racing Ver. 2.0
So picking up a 99 and here we go. All bolt-on and/or upgraded parts are going to be pulled form my 02 mp62 car and put into to the 99 but first there will be some track prep work (unless the money runs out)
02 car
99 day 1
02 car
99 day 1
Last edited by jeff_man; 04-25-2010 at 11:23 PM.
Reply
0
0
04-15-2010, 12:14 PM
#6
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
William gave me a box of some unknown pads he was about the throw away, dct60 will be in stock before i will have needed them. I got bored and started stripping the car a week early. I'll buy you a bear for the effort 
Reply
0
0
04-19-2010, 05:41 PM
#9
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
suspension, swaps, brake lines are off the 99 car and will be putting them on the 02 car this weekend. will pull the roll bar, flex, racing beat sway and end links off the 02 car to put in the 99 car.
Reply
0
0
04-25-2010, 11:32 PM
#10
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
pulled flexes, stainless lines, sway bars and end links from the 02 car and put all stock back.
flexes in
found where the body is bent making the bumper sag
flexes in
found where the body is bent making the bumper sag
Reply
0
0
04-28-2010, 02:31 AM
#11
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
O2 car is now as stock as it will get other then the clutch and flywheel to come out later.
pulled in the last 2 days and replaced with oem (may forget somethings)
PWR radiator, Power plant frame brace, tdr intercooler, jr header, strut tower brace, ducting, mp62 w/ all mounting hardware, injectors, lc1, gauges, power cards, power steering cooler, throttle body, and all the modified stuff needed to make it all fit.
also made a cold side intake
before
after
pulled in the last 2 days and replaced with oem (may forget somethings)
PWR radiator, Power plant frame brace, tdr intercooler, jr header, strut tower brace, ducting, mp62 w/ all mounting hardware, injectors, lc1, gauges, power cards, power steering cooler, throttle body, and all the modified stuff needed to make it all fit.
also made a cold side intake
before
after
Reply
0
0
07-26-2010, 12:30 AM
#12
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
soooo.. updates.
johnwag helped me install a fm stage 1
i got bored and make my 99 gauges blue
removed a few lbs in bolts
bumped my bump stops and have to replace 2
6uls 15x9 showed up and i wish i was at the install them on the car stage
johnwag helped me install a fm stage 1
i got bored and make my 99 gauges blue
removed a few lbs in bolts
bumped my bump stops and have to replace 2
6uls 15x9 showed up and i wish i was at the install them on the car stage
Reply
0
0
07-26-2010, 12:41 AM
#13
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
Started to install gauges and cluster today but ended with a oil press that goes to max position unless i ground out the sender wire. have to call vdo tomorrow and see if i'm stupid or the gauge is dead.
my pre k wiring diagram
wiring harness because after you pull and dash once and have to cut and rewire everything to get the dash out, you install quick connects
soldering is run...
done... kinda
making sure everything works before i strap it all into the dash and guess what, oil press doesn't work
added a high powered turbo fan and ducting to bring in less hot fresh air, for when you stuck in traffic and have no ac
and some ricer stickers
my pre k wiring diagram
wiring harness because after you pull and dash once and have to cut and rewire everything to get the dash out, you install quick connects
soldering is run...
done... kinda
making sure everything works before i strap it all into the dash and guess what, oil press doesn't work
added a high powered turbo fan and ducting to bring in less hot fresh air, for when you stuck in traffic and have no ac
and some ricer stickers
Reply
0
0
08-09-2010, 03:29 PM
#18
So why are you switching from the 02 to the 99?
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Reply
0
0
08-09-2010, 04:17 PM
#19
Elite Member
Thread Starter
iTrader: (7)
Join Date: May 2007
Location: Dallas, Tx
Posts: 3,006
Total Cats: 103
vvt was the first reason but after i bot the 99 Adaptronic found the vvt problem with there ecus and fixed it. biggest reason and 2nd. i didn't want to gut my 02, it's still a nice car so i picked up a trashes and scratched up 99 that i can beat up and not care.
Reply
0
0
