|
Thanks man.
We do get some pretty nice cars down here yeah. We used to have a 1/8th mile strip but that went sour. Up until last year we did have a monthly Auto cross. We use an industrial estate as it's all we can get permission to use. 2016 we may have a better venue lined up. |
no ATS carbon. Opted to get an new ORC single plate instead. Worked out cheaper than the FM kit. Everything will be here in September so if the damned rain would stop I could get a move on and have the car put back together by then.
|
I have gotten absolutely nothing done since I last posted.
Hurricane season started on June 1st and the weather has only now just gotten better. The company I was working for out sourced the store I was working at so I had to dedicate my time to re-interviewing for my position with the new company (which I got thankfully:cool:) I did manage to order a few bits and pieces V8roadster frame rails, HD sway bar mounts & the engine bay re-enforcement plates for when you have to cut the wings to clear a V8. Delrin engine mounts ARP head studs Cometic head gasket Felpro rear main seal Mac 3 port solenoid to wire into the Haltech 3" compressor inlet adapter The hardtop, suspension, diff & clutch/flywheel will be here end of August :party: Tuesday is my next day off and if it's not raining I'll finish the wheel wells & prep the frame rails with the bfh. |
2 Attachment(s)
Finally remembered to go pick up the calipers I got off Scrambles part out.
https://www.miataturbo.net/attachmen...ine=1435025119 https://www.miataturbo.net/attachmen...ine=1435025119 Cleaned them up and shot them with Duplicolor red caliper paint. Realized a bit too late that I ordered the 0.040" head gasket and not the 0.070". Would have been nice to drop the compression from the 9.4:1. I guess I'll have to keep the boost low :( |
1 Attachment(s)
The only picture I managed to snap was this. I still need to clean and weld the bottom part of the piece that goes across the rear of the wheel well.
https://www.miataturbo.net/attachmen...ine=1435091906 The rear is finished, rear base plates for the cage are in and I cut the rust out front behind the drivers side seat belt tower. The seams are cleaned for the drivers side wheel wells but I just did not have the stamina to finish them (went to the gym this morning) I can't wait to douse this thing in degreaser and pressure wash the crap out of it so my brother can paint the interior and bay. |
1 Attachment(s)
Well the hard top didn't fit in the container :crx:. Will be coming later on in the year on the next one. But the clutch, diff & coilovers are coming so I have that going for me which is nice.
Freight forwarder says next week for all the other shit from Miami. Also ordered manifold and down pipe materials The head flange & turbine inlet I ordered from Turbo-Flanges.com: Alloy, Stainless Steel and Titanium flange products for the head, turbine inlet and outlet. and the rest from acerace https://www.miataturbo.net/attachmen...ine=1435753623 Hoping to take some time off in august to speed the process up. |
4 Attachment(s)
Decided to make the best of the hard top not coming on this container so I ordered 3 friends to keep it company.
Got some used AutoExe underbraces and a Mazdaspeed 3 point front strut tower brace. https://www.miataturbo.net/attachmen...ine=1435853600 https://www.miataturbo.net/attachmen...ine=1435853600 https://www.miataturbo.net/attachmen...ine=1435853600 https://www.miataturbo.net/attachmen...ine=1435853600 I didn't save a pic of the AutoExe auction before it ended so just for reference What I want to take a look at when I get the rear one mounted is if there is any way I can tie the diff end of the PPF into it. Once I get fender braces & the 949 swaybar package the chassis/suspension will be complete. |
A friend want's me to redo his intercooler setup on his Evo3 so he's bought me the Vibrant 18x6.5x3.25 core for the Miata as payment for the work.
Plan is to use some 3/16" sheet to make some end tanks to point the piping up so I can do an over the rad setup. All I need now is some 2" aluminum bends & piping and the oil/water lines for the turbo kit to be complete. This is all coming together alot quicker than I imagined. Need to get my ass in gear and finish the seam welding. |
16 Attachment(s)
Pics!
https://www.miataturbo.net/attachmen...ine=1436476513 V8R engine bay gussets https://www.miataturbo.net/attachmen...ine=1436476513 V8R sway bar mounts. I might add some end caps/gussets for the hell of it https://www.miataturbo.net/attachmen...ine=1436476513 V8R frame rails. I asked if they could send me some uncoated ones so I could weld them in. The bolts feel like they weigh more than the frame rails. https://www.miataturbo.net/attachmen...ine=1436476513 Cometic 0.040" head gasket. I ordered what I thought were head studs but turned out to be main studs. A slight mis-click of the mouse as it were https://www.miataturbo.net/attachmen...ine=1436476513 3" inlet adapter for the T25. I got it from ebay seller custom.control. It did not come with an O-ring which seems kinda lame but it's ebay so *shrug* https://www.miataturbo.net/attachmen...ine=1436476513 Mac 3 port to wire into the Haltech https://www.miataturbo.net/attachmen...ine=1436476513 I'll see how long my fillings stay in with these delrin engine mounts:giggle: https://www.miataturbo.net/attachmen...ine=1436476513 Other than those I ordered some small bits from Andrew at Trackspeed, front coolant block off since I have the Skou reroute and some fittings for a Mocal sandwich adapter I had left over from another project. |
7 Attachment(s)
Well I got some work done last weekend and tomorrow I'm at it again with the wire wheel.
https://www.miataturbo.net/attachmen...ine=1437666788 https://www.miataturbo.net/attachmen...ine=1437666788 Spent about an hour cleaning the undercoating off the passenger side and swatting the frame rail with a hammer to get it into decent enough shape to test fit the V8roadster rails. As you can see...still much more cleaning to be done before I can weld *ugh* Also some goodies came today https://www.miataturbo.net/attachmen...ine=1437666788 The Vibrant cores look pretty good on the inside. I got the 18x6.5x3.25 core and some 3/16" aluminum sheet to make end tanks ]img]http://img.photobucket.com/albums/v489/Sirnixalot/Miata%20Turbo%20Pix/557E83EB-C484-4A40-80A3-92DDD9888A05_zpsevjoogfr.jpg[/img] https://www.miataturbo.net/attachmen...ine=1437666788 Some surface rust on the flanges but other than that in great shape. Got them from Turbo-Flanges.com: Alloy, Stainless Steel and Titanium flange products for the head, turbine inlet and outlet. https://www.miataturbo.net/attachmen...ine=1437666788 1.25" weld el's are so small compared to the 1.5" ones I am used to https://www.miataturbo.net/attachmen...ine=1437666788 Weld el's, pipe and down pipe materials from acestainless https://www.miataturbo.net/attachmen...ine=1437666788 I'll be cutting that V-band off and just welding a bend directly to the adapter Tomorrow the plan is to get the rest of the underside cleaned up so I can finish all the welding next week. I MIGHT see if I can get the engine and transmission back in the engine bay. |
4 Attachment(s)
Holy fuck it's hot today.
I called it quits at about 1pm. https://www.miataturbo.net/attachmen...ine=1437769137 Aligned and welded in the main hoop and rear legs of the cusco cage. Gussets will be made to tie the main hoop to the B pillar and I might see if I can tie the rear tubes to the seat belt towers some how. I am going to leave the front half as bolt in. I have the hardware to weld to the A pillar and top of the windshield opening to bolt the 3 pieces of the cage to. https://www.miataturbo.net/attachmen...ine=1437769137 I cut the v-band off the adapter from acerace and hammered it back into round so I can weld it directly to the 90* when the time comes. Also added a divider wall. https://www.miataturbo.net/attachmen...ine=1437769137 Ebay compressor outlet adapter is a little.....off center. Will be running it as is. I plan on blocking off the boost port. https://www.miataturbo.net/attachmen...ine=1437769137 The T25 in all it's old glory I got the drive train ready to slide back under the car for the manifold and downpipe fab. I am trying to use that as my "reward" if I stop procrastinating in regards to the seam welding :rofl: |
4 Attachment(s)
Rust repair!
https://www.miataturbo.net/attachmen...ine=1438980399 Not quite finished but it looks a ton better than it was before. I still have the piece on the right of the pic to repair as well https://www.miataturbo.net/attachmen...ine=1438980399 Passenger side trans tunnel. It's fully welded on the underside and I still have to finish the welds on the top side before I slather the welds in sealant https://www.miataturbo.net/attachmen...ine=1438980399 A friend helped me get the motor/trans back in the car for manifold and down pipe mocking up. You can spy one of the $40 ebay delrin engine mounts. https://www.miataturbo.net/attachmen...ine=1438980399 Degreased the front of the motor, installed the TSE reroute block off, changed the front main seal and water pump. Inspecting under the valve cover I found caked oil residue on all the things :vash: Since I am taking the head off to do the head gasket I'll just oven cleaner and diesel the crap out of it before re-installation. I got pretty much all of the drivers side, gas tank area and transmission tunnel wire wheeled. Next challenge is the drivers side wheel wells and underside. The coilovers, torsen diff & clutch/flywheel will be here next weekend. A friend is bringing back the windshield seal and some oem stuff from Canada in 2 weeks. Things are coming together, I just need 2 solid days of over cast skys to finish the welding.....it's fucking HOT down here |
5 Attachment(s)
The wife gave me a few hours this evening so I set to work on the manifold.
https://www.miataturbo.net/attachmen...ine=1439178939 Made a jig https://www.miataturbo.net/attachmen...ine=1439178939 Test cuts on pcv successful https://www.miataturbo.net/attachmen...ine=1439178939 Time for the real thing! https://www.miataturbo.net/attachmen...ine=1439178939 Fast forward a bit and I have the collector and easiest runner tacked https://www.miataturbo.net/attachmen...ine=1439178939 Pizza slices are in my down pipes future I am hoping I can get away with a cast 2" elbow off the compressor for over the radiator piping. It looks a little tight with the timing cover. The intake piping is dead simple at least |
Wow, you've been busy.
|
Looking good!
Hopefully I finish my manifold before you do haha. I wish I would have followed your posts on seam welding... That tar glue stuff gave me some trouble this weekend... |
I'll be back at the car on friday. I really need to concentrate on finishing the chassis so my brother can paint it and I can get it back to a rolling shell. Something tells me I will be distracted by the manifold and down pipe fab.
That seam sealant stuff is the worst. I do NOT envy you for using a Tig for those door bar mounts. I am wondering if I shouldn't make some door bar's as well but my main issue is lack of a tubing bender or DOM tube locally. Not sure if I will see the same benefit after having seam welded the door openings as well as all the rocker panel seams? |
3 Attachment(s)
Not sure if I am mistaking a brain tumor for an idea or not. Around the side of the radiator intercooler piping? I am trying to keep the run short but I'm not really feeling the over the radiator routing.
https://www.miataturbo.net/attachmen...ine=1439243426 I know if I cut out this area I can fit 2" https://www.miataturbo.net/attachmen...ine=1439243426 View from the front https://www.miataturbo.net/attachmen...ine=1439243426 The thing in the bubble wrap is the vibrant core. I can get a nice angled shot at the core. The cold side is a fairly similar ordeal. *scratches chin* |
Round 2: Wannabe turbo NB6C
Most of us go down under the frame rails and around the outsides of the radiator.
|
2 Attachment(s)
Thats how Pat did his intercooler:
https://www.miataturbo.net/attachmen...ine=1439310783 https://www.miataturbo.net/attachmen...ine=1439310783 |
I was hunting for a while and that didn't show up in any searches. Really didn't feel like necromancing a thread from 2011. Thanks for the pictures.
I'll have to think about it some more. I don't honestly think the extra 3-4ft of piping will really matter in the grand scheme but I want to try and keep it as short as possible because 1.6 |
| All times are GMT -4. The time now is 05:21 PM. |
© 2024 MH Sub I, LLC dba Internet Brands