Any ideas on the thermostat?? And should a coolant reroute be done?

Also can I tap into the stock water temp sender for a guage??

You don't need anything colder than a 160 and you don't have to do a reroute though they are nice. The stock water temp sender is not the right resistance for your gauge. You need to use the sender that is made for your gauge or vice versa.

Can I just add a resistor in line with the temp gauge to get the correct reading?

Just linearize your stock temp gauge. There's instructions online if you poke around.

So I tapped my oil pan last night and really recommend using a slightly larger drill than the 45/64. The amount that I could thread the tap in did not get the threads big enough to get the fitting to thread in. I had to file the fitting down a little and it was a pain.

I will have some more pretty pics of my progress soon!!

Pretty sure 11/16 is a better drill bit to use.

On a side note... Vmounts will take over the world!

I ran a 23/32" and had no issues. I didn't get the fitting too far in, but then again there aren't too many threads in the pan anyway.

Here is are pics of the manifold all tacked together and placed on the engine. It looks like it will fit perfect and give a great angle out the back for the downpipe. I am going to tig weld it at a friends place tomorrow instead of mig'ing it and having it look UGLY. Like that matters......but it is a sweet manifold for $175 and a poo-load of grinding time.

http://i243.photobucket.com/albums/f...d/IMG_1573.jpg
Attachment 215860
Attachment 215861

I also got the tranny back in today with the F1 stage 3 clutch that will hopefully work ok because it was a pain getting that tranny out. Next up it completing the intercooler mount and running all of the intake tubing, the the downpipe and exhaust.

So now I am trying to put my boost gauge in the eyeball vent by the door and I cannot figure out how to get the bezel off?? I hear that they are suppose to pop out but it will not. Is this one different than the two in the middle? ??

No idea about the vent. Who made your flanges for the manifold?

flipside customs made the exhaust flange and ATP made the turbo flange. Both 1/2" 304 stainless.

Here are pics of the manifold all tig welded together:

http://i243.photobucket.com/albums/f...d/IMG_1585.jpg
http://i243.photobucket.com/albums/f...d/IMG_1586.jpg

And a mock up of how I will route the piping:

Attachment 215857
http://i243.photobucket.com/albums/f...d/IMG_1587.jpg

Hopefully I can finish the rest of the exhaust and intercooler piping this weekend??

Check out the album link in my first post for the rest of the pics.

Nice welding it came out well. You plan to get it coated?

No, what would I gain, and what kind of coating are you talking about? Ceramic??

High temp ceramic coating such as jethot 2000. The ceramic coating won't flake off, it looks nice. It also retains heat really well and can increase spool due to less lost energy by heat retention. You don't need it but it's cool stuff.

Is it a bad idea to make heat shields out of aluminum? I have a bunch of it??

OEM car manufacturers make heatshields out of aluminum. Should be fine. Louvered aluminum would be awesome.

I got the intercooler and radiator all mounted and tacked up the downpipe today. I will post pics soon...it is going very well. Hopefully it runs just as well.

As a side note the oil drain flange from the JGS Turbo kit does not fit the SR20 turbo. Too small. Also the bolt pattern on the ATP turbo outlet flange was slightly off and I had to grind it to make it fit. Oh well.

Here is the current progress:

I have built the 3" stainless exhaust. It has a Magnaflow straight through muffler and 3" catalytic converter. The downpipe has a 3" flex bellow and has a divorced wastegate tube at the top. I made two custom 90* transitions, 2.25"-2.5" and 2.5"-3". I just calculated what the circumference should be and cut out the difference in a v-shape. Then i squeezed it together in my vice, welded it together and cut the end flat.

http://i243.photobucket.com/albums/f...d/IMG_1596.jpg
http://i243.photobucket.com/albums/f...d/IMG_1602.jpg
http://i243.photobucket.com/albums/f...d/IMG_1603.jpg

I also finished welding up a bunch of small changes on the turbo inlet and outlet, changing their direction, changed the water pump outlet direction.....a buch of small stuff. Including welding the BOV flange to the intercooler end tank due to lack of room by the throttle body.

I am hoping to start the car tomorrow night but may push it back until thursday just to make sure everything is good to go. Check out the other pictures at:

http://s243.photobucket.com/albums/ff276/kylelind/