Boost solenoid Position With Manaul Boost Controller
#1
Boost solenoid Position With Manaul Boost Controller
My turbo doesnt have a vacuum pipe going from the compressor to the actuator so instead I have had to take a line from the vacuum source on the inlet manifold.
Where do I need to position the boost solenoid as I have a manual boost controller between the actuator and the inlet vacuum source.
Does it go after the Manual boost controller but before the actuator so it picks the boost up when the Manual boost controller has increased the boost as it reads the boost going through the turbo?
Or does it go after the Manual boost controller between that and the inlet source so it detects the boost before the controller has increased it?
Or an Other area?
Thanks
Andy
Where do I need to position the boost solenoid as I have a manual boost controller between the actuator and the inlet vacuum source.
Does it go after the Manual boost controller but before the actuator so it picks the boost up when the Manual boost controller has increased the boost as it reads the boost going through the turbo?
Or does it go after the Manual boost controller between that and the inlet source so it detects the boost before the controller has increased it?
Or an Other area?
Thanks
Andy
#2
It should basically go where your manual boost controller is now (in between the line that actuates the wastegate. Basically it's just a valve that will open and let pressure go through once it reaches a certain threshold. On another note, you need to take your wastegate signal before the throttle body.
#4
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,675
Total Cats: 3,017
Dustin is right. Do not take the wastegate actuator signal from the intake manifold. Take it somewhere between the intercooler and the throttle body.
Why do you want to run both a manual and an electronic boost controller? Why not just the electronic one?
#5
OK I may have made a mistake!
I have gone and bought a manual boost controller as a means to increase the boost upto 14-15 psi. Dont tell me I have wasted my time as the EBC does that for me?
If so does it go between the actuator and the inlet manifold as thats where I have had to take the pipe to?
Also how does it increase the boost via the MS tuning software?
Thanks for your patience believe me I feel dumb!
I have gone and bought a manual boost controller as a means to increase the boost upto 14-15 psi. Dont tell me I have wasted my time as the EBC does that for me?
If so does it go between the actuator and the inlet manifold as thats where I have had to take the pipe to?
Also how does it increase the boost via the MS tuning software?
Thanks for your patience believe me I feel dumb!
#7
There is nowhere to 'T' off. I was told to take it from the pipe on the top of the inlet manifold. I could take it from the line where the fuel pressure regulator is at the back left of the engine bay? I already have my ECU piped into that as instructed.
Or can you suggest where to pipe it?
#10
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,675
Total Cats: 3,017
Where can I take the pipe from then?
There is nowhere to 'T' off. I was told to take it from the pipe on the top of the inlet manifold. I could take it from the line where the fuel pressure regulator is at the back left of the engine bay? I already have my ECU piped into that as instructed.
Or can you suggest where to pipe it?
There is nowhere to 'T' off. I was told to take it from the pipe on the top of the inlet manifold. I could take it from the line where the fuel pressure regulator is at the back left of the engine bay? I already have my ECU piped into that as instructed.
Or can you suggest where to pipe it?
What is your air fuel ratio in boost currently? And how many pounds of boost?
#15
You must add a small fitting for the little hose. You need to take the signal from there. If there was another location that would be easier and work properly I would tell you so. I would suggest that with your limited technical experience it might be preferable for you to use the manual boost controller.
What is your air fuel ratio in boost currently? And how many pounds of boost?
What is your air fuel ratio in boost currently? And how many pounds of boost?
Its almost finished now just the boost controller, heater matrix pipe and a downpipe to buy (Which im arranging with Abe) then I can get it started and see how it runs.
#17
Ok so after 5 pages of informative reading the consensus is that taking the feed from point 'B' is the best point.
That does create a few issues for me as I could only really do that from the pipe I have added just before the throttle body but that already has my BOV, AIT sensor, and idle valve pipe welded into it. So adding another pipe for that would be too congested.
I have a stainless steel 90 degree bend which comes out the TB side of the intercooler which I could tap and I suppose from what was said that should be fine.
2 things off topic.
1st the BOV feed. Brain you said to take the feed for this before the TB? Someone replied after that to say take it from after the TB. Is it ok to take it after?
2nd I dropped my AIT sesnor and smashed the white plastic around the sensor. But the sensor itself looks ok. Can it still be used as its exposed and not protected? I picked off all the white plastic so none could go into the engine.
That does create a few issues for me as I could only really do that from the pipe I have added just before the throttle body but that already has my BOV, AIT sensor, and idle valve pipe welded into it. So adding another pipe for that would be too congested.
I have a stainless steel 90 degree bend which comes out the TB side of the intercooler which I could tap and I suppose from what was said that should be fine.
2 things off topic.
1st the BOV feed. Brain you said to take the feed for this before the TB? Someone replied after that to say take it from after the TB. Is it ok to take it after?
2nd I dropped my AIT sesnor and smashed the white plastic around the sensor. But the sensor itself looks ok. Can it still be used as its exposed and not protected? I picked off all the white plastic so none could go into the engine.
#19
BOV should be after TB but as close as possible
the IAT is just a thermistor (temperature variable resistor) So should be fine.
I suppose technically point b would make sense but what if you get a leak or a boost pipe comes loose ?? wouldn't the car just keep boosting till it went bang?
(Kind of)
I would rather loose a bit of boost and be reliable I don't use mine for racing but I do use it for long jouneys
the IAT is just a thermistor (temperature variable resistor) So should be fine.
I suppose technically point b would make sense but what if you get a leak or a boost pipe comes loose ?? wouldn't the car just keep boosting till it went bang?
(Kind of)
I would rather loose a bit of boost and be reliable I don't use mine for racing but I do use it for long jouneys