keep dreaming...i do!!! LOL
|
2 Attachment(s)
Had to send the F/IC back to AEM to get looked at. Would run good if I held the harness just right. Otherwise, was experiencing signal dropout, rough running, cel, etc., whenever I moved the harness around. Runs fine with the bypass plug installed. The bypass plug pins look to be larger that those on the F/IC which I think may have caused the sockets in the harness connector to enlarge.
Didn't like the way the A-pillar pod blocked the view so went with a TDR gauge panel. Slotted the inner shift boot to route the O2 cable through. Attachment 215234 Attachment 215235 |
That's the TDR panel? That's the same thing i have, $20 shipped on ebay.
|
How do you keep it from falling out?
Stephanie |
1 Attachment(s)
Originally Posted by cjernigan
(Post 176851)
That's the TDR panel? That's the same thing i have, $20 shipped on ebay.
Originally Posted by Stephanie Turner
(Post 176852)
How do you keep it from falling out?
Stephanie Attachment 215233 |
Yep exact same thing. Guess they're making some major bank on those.
http://tinyurl.com/2mq5th The trim panel that goes around it all hold it in well too. |
any updates on your ecu?
|
Originally Posted by gdnimr0d
(Post 177197)
any updates on your ecu?
|
its Dec....?
|
i wish I had ceramic coating on my kit.
|
1 Attachment(s)
|
You can get one just like it on ebay. Or anplumbing.com sells them. Should be 20mm, pretty sure the civic uses the same thread. Glowshift sells them.
|
20x1.5 is what you need for a sammmmich plate.
keep us updated on the AEM install, i just picked one of those up... |
How is the turbo install coming? Any new photos?
Stephanie |
Originally Posted by Stephanie Turner
(Post 186596)
How is the turbo install coming? Any new photos?
Stephanie |
Just to follow up on the F/IC problems I'm having. AEM looked at the unit and couldn't find anything wrong with it and sent it back along with a new harness. Wired the new harness in and still having the same problem with the engine running rough/dieing when the unit is moved around. Runs fine with the bypass harness installed. Sent AEM some vids to show them.
http://s16.photobucket.com/albums/b3...ssHarnness.flv http://s16.photobucket.com/albums/b3...CInstalled.flv |
those videos seem pretty conclusive to me.
|
did u cut of the spliced sections of the harness?? theres a possibility that they are contacting each other when moving. but its kinda hard to see in the video... im running the same set up as you (like scary identical) but on my 01. f/ic w/ uego and everything is wired up and it runs like stock. (havnt gotten to install the turbo yet)
|
Originally Posted by emmi
(Post 189537)
did u cut of the spliced sections of the harness?? theres a possibility that they are contacting each other when moving. but its kinda hard to see in the video... im running the same set up as you (like scary identical) but on my 01. f/ic w/ uego and everything is wired up and it runs like stock. (havnt gotten to install the turbo yet)
|
okay well i regretted doing this but the problem is in v2 which i recall u do having frm the video...
i just updated mine right now and my car got hella fucked up... im trying right now to downgrade back to V1 damn.... it idled, then it threw a CEL and it started bogging and drastically changing idle... |
All times are GMT -4. The time now is 10:41 PM. |
© 2024 MH Sub I, LLC dba Internet Brands