Flanges!
#1
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2005
Location: Houston, TX
Posts: 811
Total Cats: 0
Flanges!
I now have the ability to cut flanges in pretty much any thickness you'd want.
I already have the BP head flange, which I drew in cad last week, just need to cut one and fit it for testing.
I also have the mitsu (14b, 16g, 20g) turbine inlet and downpipe flanges.
To cut something custom, I either need what it's bolting to, or a gasket, or a really good drawing of the item.
I'm still working on pricing for materials, but I think I can be reasonable on pricing.
I already have the BP head flange, which I drew in cad last week, just need to cut one and fit it for testing.
I also have the mitsu (14b, 16g, 20g) turbine inlet and downpipe flanges.
To cut something custom, I either need what it's bolting to, or a gasket, or a really good drawing of the item.
I'm still working on pricing for materials, but I think I can be reasonable on pricing.
#7
Unless its a commercial unit... they can cut pretty clean.
I tend to like cnc/laser/waterjet first though for their cleanliness/precision.
Post up a pick of how the plasma leaves the flanges. Would help for those that picture Plasma as a handheld slag machine.
I tend to like cnc/laser/waterjet first though for their cleanliness/precision.
Post up a pick of how the plasma leaves the flanges. Would help for those that picture Plasma as a handheld slag machine.
Last edited by Splitime; 06-05-2007 at 04:10 PM.
#8
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2005
Location: Houston, TX
Posts: 811
Total Cats: 0
We have a commercial grade cutter, which goes with the table.
I don't have any finished flanges on hand right now, just some of our first prototypes with do look pretty rough, as we got the machine dialed in.. As soon as we got some good ones, we shipped them out asap..
As far as slag goes, it's very minimal. Most of it came off by running my finger nail over, the rest came off with a wire wheel.. you're looking at like 30 seconds to a minute of prep for a downpipe type stuff..
I will look for some pics and post later.
I don't have any finished flanges on hand right now, just some of our first prototypes with do look pretty rough, as we got the machine dialed in.. As soon as we got some good ones, we shipped them out asap..
As far as slag goes, it's very minimal. Most of it came off by running my finger nail over, the rest came off with a wire wheel.. you're looking at like 30 seconds to a minute of prep for a downpipe type stuff..
I will look for some pics and post later.
#13
Senior Member
Thread Starter
iTrader: (6)
Join Date: Sep 2005
Location: Houston, TX
Posts: 811
Total Cats: 0
it takes me between 10 minutes to an hour to draw something, it takes under a minute to cut something like a downpipe flange..
For example, we can cut 3/8" plate at like 35-41 inches per minute, and 1/8" plate at like 210 inches per minute..
Here's where we've been testing..
Here's a cut on a 1/4" plate..
3/8" plate
Here's the underside of the plate, for an example of the slag.
For example, we can cut 3/8" plate at like 35-41 inches per minute, and 1/8" plate at like 210 inches per minute..
Here's where we've been testing..
Here's a cut on a 1/4" plate..
3/8" plate
Here's the underside of the plate, for an example of the slag.
#14
Senior Member
iTrader: (6)
Join Date: Mar 2005
Location: Sammamish, Washington
Posts: 1,396
Total Cats: 0
My fiance does bitch. They are actually pretty bad ***. She got 40 mpg with it loaded up on her drive from Colorado to Washington. They weigh under 2400 lbs so 150 whp would make it pretty entertaining to drive.