Got an gt2876r on ebay... Now want to fit it on my HKS mani...
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: Haarlem ,the Netherlands
Posts: 453
Total Cats: 0
Got an gt2876r on ebay... Now want to fit it on my HKS mani...
Got lucky today: A 1500km (1100miles old) garrett gt2876r aka gt2540r.
Bought it for 268euro (350dollar)
Owner garranteed the turbo is in working condition.
http://cgi.ebay.nl/ws/eBayISAPI.dll?...m=130257612528
Now the next problem: Will this clear my hood with a HKS mani (1.8 NA)???
As i won today, i don't have it yet...
If anyone else have the same turbo i want to have one measurement:
From the center off the compressor wheel to the side, exactly where the 0 (zero) of the .70 a/r.
I measured my gt2560, it's about 7.5 cm....
Calculating from the pics found on internet I need about 2 cm max to clear my hood.
Bought it for 268euro (350dollar)
Owner garranteed the turbo is in working condition.
http://cgi.ebay.nl/ws/eBayISAPI.dll?...m=130257612528
Now the next problem: Will this clear my hood with a HKS mani (1.8 NA)???
As i won today, i don't have it yet...
If anyone else have the same turbo i want to have one measurement:
From the center off the compressor wheel to the side, exactly where the 0 (zero) of the .70 a/r.
I measured my gt2560, it's about 7.5 cm....
Calculating from the pics found on internet I need about 2 cm max to clear my hood.
#3
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: Haarlem ,the Netherlands
Posts: 453
Total Cats: 0
It's helpfull, looks like i need 1.5 cm... Maybe raise the hood slightly???
I have to point it down as much as possible.
Looks like it would work...
What are your experiance with this turbo??
Boost pressure at what rpm??
aiming for 10 psi (engine is stock 95, with 99 head) so i need to keep HP down.(maybe play with the cam gears)
Some forged rods and pistons are next... Also ordered the oil pump gears a while back.
Always wanted to upgrade the 2560... As (see the my name) i started with a greddy turbo, I always liked the high rpm boost kick...
I have to point it down as much as possible.
Looks like it would work...
What are your experiance with this turbo??
Boost pressure at what rpm??
aiming for 10 psi (engine is stock 95, with 99 head) so i need to keep HP down.(maybe play with the cam gears)
Some forged rods and pistons are next... Also ordered the oil pump gears a while back.
Always wanted to upgrade the 2560... As (see the my name) i started with a greddy turbo, I always liked the high rpm boost kick...
#4
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
on a 99 head motor you'll see 10 psi around 3800-4200RPM.
with good tuning that's probably 240-250rwhp give or take.
Here's my car at 9.5 psi (stock 2001 motor)
Look at the overlapping red and green lines (the vvt is disabled in those)
It's not a bad turbo, but it really is better suited for more boost or a slightly bigger motor.
with good tuning that's probably 240-250rwhp give or take.
Here's my car at 9.5 psi (stock 2001 motor)
Look at the overlapping red and green lines (the vvt is disabled in those)
It's not a bad turbo, but it really is better suited for more boost or a slightly bigger motor.
#5
Junior Member
Thread Starter
iTrader: (1)
Join Date: Oct 2004
Location: Haarlem ,the Netherlands
Posts: 453
Total Cats: 0
So you retarded the timing 12 degrees on the exhaust side and found 250 hp on 10psi?? Nice!
I can see the potential.
Does that mean that the more boost you run the more retarded the exhaust timing should be?
My engine is ok with 12-14 psi off the 2560... (link ecu)
I can see the potential.
Does that mean that the more boost you run the more retarded the exhaust timing should be?
My engine is ok with 12-14 psi off the 2560... (link ecu)
#14
yer fully built motor @ 15psi runs just a tad over 300bhp
it clears the bonnet just the noise from it is amazing
weiscos
carllio rods
lightened, balanced and knife edged crank
lightened flywheel
padle clutch
quife straight cut box
3angled valves
uprated valve springs
solid lifters
obx cams
vernier pulleys
rc 750 p&h low imp injectors
tunertoyz duel feed fuel rail
areomotive external fuel pump
swirl pot
walbro internal fuel pump
sard pres reg
front mount intercooler
oil cooler
alloy rad
hydra ems
hispec 4pot calipers with 305mm floating discs
gaz coilovers
custom exhaust manifold
gt2876r ball bearing turbo
collins -31 actuator
custom downpipe
wide band o2
3" exhaust from turbo back
digi dash
momo seats all sound proofing removed and carpets refitted
the list goes on all the work has been carried out by myself including the manifold
and the mapping
sorry to steel your thread lol
it clears the bonnet just the noise from it is amazing
weiscos
carllio rods
lightened, balanced and knife edged crank
lightened flywheel
padle clutch
quife straight cut box
3angled valves
uprated valve springs
solid lifters
obx cams
vernier pulleys
rc 750 p&h low imp injectors
tunertoyz duel feed fuel rail
areomotive external fuel pump
swirl pot
walbro internal fuel pump
sard pres reg
front mount intercooler
oil cooler
alloy rad
hydra ems
hispec 4pot calipers with 305mm floating discs
gaz coilovers
custom exhaust manifold
gt2876r ball bearing turbo
collins -31 actuator
custom downpipe
wide band o2
3" exhaust from turbo back
digi dash
momo seats all sound proofing removed and carpets refitted
the list goes on all the work has been carried out by myself including the manifold
and the mapping
sorry to steel your thread lol
Last edited by madmalc; 10-01-2008 at 01:31 PM.
Thread
Thread Starter
Forum
Replies
Last Post
bigmackloud
Miata parts for sale/trade
19
01-08-2021 11:24 AM
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM