COP testing
#1
Elite Member
Thread Starter
iTrader: (18)
Join Date: Dec 2007
Location: oahu
Posts: 1,787
Total Cats: 6
COP testing
Anybody know how to test cops? I did some interweb searching and mt searching and have not come up with anything helpful. Can somebody impart some resistance values I should see (mainly thinking the resistance across the driver will be most important/helpful and I think it should be around 5k). Thanks!
#2
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,076
Total Cats: 6,628
1: Put the ignition coil on the bench.
2: Have a source of 12 volts available, such as a car battery. A wall-wart probably won't cut it unless it's rated for well over 1000ma (1A), and more is better here.
3: Insert a spark plug into the coil.
4: Take a length of wire, strip one end several inches, and wrap that end around the threaded portion of the spark plug, securing it with tape, zip-tie, etc. Connect the other end of the wire to the GND or (-) side of the 12v power supply.
5: Connect the (+) and (-) terminals of the coil to the 12v power supply.
6a: When I've done this, I have had a second power supply available to supply 5v to the trigger input. This one can be a small wall-wart, or one of those battery holders that puts 3 AA batteries in series.
2: Have a source of 12 volts available, such as a car battery. A wall-wart probably won't cut it unless it's rated for well over 1000ma (1A), and more is better here.
3: Insert a spark plug into the coil.
4: Take a length of wire, strip one end several inches, and wrap that end around the threaded portion of the spark plug, securing it with tape, zip-tie, etc. Connect the other end of the wire to the GND or (-) side of the 12v power supply.
5: Connect the (+) and (-) terminals of the coil to the 12v power supply.
6a: When I've done this, I have had a second power supply available to supply 5v to the trigger input. This one can be a small wall-wart, or one of those battery holders that puts 3 AA batteries in series.
i: If you have this available, connect the (-) or GND side of the 5v supply to that of the 12v supply.
ii: Tap the (+) wire of the 5v supply to the trigger pin of the coil very briefly, and the plug should spark.
6b: If you do not have a 5v supply available, you can probably get away with triggering via 12v:ii: Tap the (+) wire of the 5v supply to the trigger pin of the coil very briefly, and the plug should spark.
i: Install a 1k resistor in series with a piece of wire.
ii: Connect one end to the (+) terminal of the 12v supply, and tap the other to the COP's trigger terminal.
iii: I don't guarantee that this will work / not destroy your coil.
ii: Connect one end to the (+) terminal of the 12v supply, and tap the other to the COP's trigger terminal.
iii: I don't guarantee that this will work / not destroy your coil.
#3
Elite Member
Thread Starter
iTrader: (18)
Join Date: Dec 2007
Location: oahu
Posts: 1,787
Total Cats: 6
I just did resistance checks across all of my cops and they were all within 1% of each other. These are the values I got:
+12 to Gnd. 27KΩ
Gnd. to Trigger 346.5Ω
Gnd. to Tach. 0Ω
+12 to Tach. 485.8KΩ
+12 to Trigger 27.2KΩ
+12 to Gnd. 27KΩ
Gnd. to Trigger 346.5Ω
Gnd. to Tach. 0Ω
+12 to Tach. 485.8KΩ
+12 to Trigger 27.2KΩ
Thread
Thread Starter
Forum
Replies
Last Post