LC1 problem
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: May 2009
Location: Niagara Falls, ON
Posts: 431
Total Cats: 2
LC1 problem
This has been pissing me off for the last year, just need some input. I hooked up my LC1 wideband last year with the digital gauge. Its working fine, reading properly on the MS, properly on the Logworks program for the LC1. LED lights up on warmup and stays on its all calibrated. The only problem is that the gauge just stays at 22.4 all the time all last year, and i would sort of like to know my AFR...not 22.4. So what wire did i **** up on? Thanks, Mike.
#2
I have personally noticed that the plug on the rear of my DB gauge is &&&uckin picky. I can be driving around, everything working fine and then out of know where the gauge starts throwing figures near the extremes and sometimes freezes at either. The way I have overcome this is that I pop the gauge and push on the plug (fixes loose or tewaked connection) => gauge goes back to normal operation.
#5
Junior Member
Thread Starter
iTrader: (1)
Join Date: May 2009
Location: Niagara Falls, ON
Posts: 431
Total Cats: 2
I have personally noticed that the plug on the rear of my DB gauge is &&&uckin picky. I can be driving around, everything working fine and then out of know where the gauge starts throwing figures near the extremes and sometimes freezes at either. The way I have overcome this is that I pop the gauge and push on the plug (fixes loose or tewaked connection) => gauge goes back to normal operation.
#12
It's a program on the disc that came with your LC-1...figured you had to have done it for you MS output, since it's normally not set up for 0-5V, 10:1-20:1...
You should also have a cable to connect laptop to the serial out (unplugged stereo jack).
Here's some instructions:
http://www.innovatemotorsports.com/r...1_tutorial.pdf
Page 8 shows LM programmer dialog box, but rest of it is geared towards EFILive use, same principle on setup though.
You should also have a cable to connect laptop to the serial out (unplugged stereo jack).
Here's some instructions:
http://www.innovatemotorsports.com/r...1_tutorial.pdf
Page 8 shows LM programmer dialog box, but rest of it is geared towards EFILive use, same principle on setup though.
#15
Junior Member
Thread Starter
iTrader: (1)
Join Date: May 2009
Location: Niagara Falls, ON
Posts: 431
Total Cats: 2
Ok just programmed it...still the same. Ground is by throttle body. And switched power source is the 12v ignition source which everything else is switched on by, i believe the yellow is going to the MS. Il go check the wires now though.
#19
Junior Member
Thread Starter
iTrader: (1)
Join Date: May 2009
Location: Niagara Falls, ON
Posts: 431
Total Cats: 2
Ok so the Gauge has 4 wires
Yellow - goes to brown on LC1
white - red LC1 and 12V
black - ground
red -red LC1 and 12V
LC1 there are 6 wires
red - white and red on gauge and 12V
blue - ground
white - ground
black - calibration button and led
brown - yellow on gauge
yellow - goes to MS
hopefully my paint skills pay off...this is how its hooked up in my car, it read correctly on MS and Logworks but not on the gauge.
Yellow - goes to brown on LC1
white - red LC1 and 12V
black - ground
red -red LC1 and 12V
LC1 there are 6 wires
red - white and red on gauge and 12V
blue - ground
white - ground
black - calibration button and led
brown - yellow on gauge
yellow - goes to MS
hopefully my paint skills pay off...this is how its hooked up in my car, it read correctly on MS and Logworks but not on the gauge.