|
No if you want 350hp it is gonna cost you 17k just for the engine just like in this thread:
This is what a 13K engine build gets you.... That is the only way. /sarcasm I died when I read the cost of his build. |
Direct Exhaust Injection.
|
obvious troll is obvious. Ban and move on please. This one is no fun.
|
Originally Posted by Braineack
(Post 954078)
I sell bell housing adapater to bolt the miata 5-sp up to that create motor. PM me.
|
so i can take his money and never give him such a stupid product...
|
Originally Posted by leatherface24
(Post 954100)
Direct Exhaust Injection.
|
Originally Posted by leatherface24
(Post 954103)
obvious troll is obvious. Ban and move on please. This one is no fun.
|
350hp
That is a lot of power for a light car.. I am not the person here with the most experiance, but it would be an easier build to to goto the ls1 build.. I am a bit older than most of the members of these forums, but unless you are a very good driver a power to weight ratio in that range can get you dead quick.. You may be someone that can manage it with no problems, but I have a few friends ( no longer with us) that misjudged their talent.. otherwise cubic inches are cheaper than art..
|
my car is under 20k including the car (it's a $500 car)
Originally Posted by Ryan_G
(Post 954098)
No if you want 350hp it is gonna cost you 17k just for the engine just like in this thread:
This is what a 13K engine build gets you.... |
holy fuuuuu 17k for an engine just to make 350whp:laugh:
|
I'm tempted to register on the site and get ready for the part out.
|
Originally Posted by cymx5
(Post 956092)
I'm tempted to register on the site and get ready for the part out.
that thread makes me nauseous and disgusted. He went full retard. not to mention he makes statements like so: Ok, so now on to your questions/comments for the week: 1.) Quote time: Yep, start your quote early. It isn't so much the overall items that need to be considered - it is actually all the subcomponents that one doesn't necessarily consider. In my case I had already done some extensive mods so a lot of time and effort was put into making sure the next step would work with where the car was already at. If possible, always jump to the last stage of a build rather than building up to it. This way integration is actually less of an issue (imo). 2.) The term "investment": Ah, ok... I wasn't really clear here. Investment usually entails the notion that one is looking to retain or make money on something. It also usually entails the notion that the item invested in WILL be sold int he future... In my case it may be a little more complex than that. I actually consider an investment in terms of what I will get out of an item in the future. This basically boils down to the notion that I will never part with Mica (probably be buried with the car). Thus, investing in her is important so that I will continue to get something (happiness, satisfaction, etc.) in the future. It doesn't hurt to know that she will probably still be worth something in the future (monetarily speaking) but there is no way I am getting my money back out of her. If you want that to a certain degree (perhaps break even? Maybe? Not really...) then you are better off with a LS swap and doing the work yourself (to offset the cost of the swap). 3.) Cost: Yep, the build does include the full stroker (thanks for the confirmation MazdaNoob). The crank alone runs $3K. p.s.I think Brain has a stroker crank in stock pm him if you're interested. It's sitting right next to his previously mentioned adapter plate. |
Thus, investing in her is important so that I will continue to get something (happiness, satisfaction, etc.) in the future |
Originally Posted by 18psi
(Post 956119)
And when all is said and done, he will be left with his thumb up his asshole like 40 grand in the hole wondering why he didn't buy lightly used c6 z06 or something like that.
:party: |
Originally Posted by krissetsfire
(Post 956115)
p.s.I think Brain has a stroker crank in stock pm him if you're interested. It's sitting right next to his previously mentioned adapter plate.
thanks, forgot about my stroker crank! |
For $3k I can get a lot of stroke on my crank.
|
Originally Posted by soviet
(Post 956227)
For $3k I can get a lot of stroke on my crank.
|
hell, for 3k I'll hone your combustion chamber
|
For $3k i might pre-detonate and blow my rod if i was honing your combustion chamber.
|
Don't forget to use some assembly lube at the rimmed tip of my piston... i got a overbored size.
|
| All times are GMT -4. The time now is 10:33 AM. |
© 2024 MH Sub I, LLC dba Internet Brands