Aftermarket pistons
#1
Elite Member
Thread Starter
iTrader: (17)
Join Date: Aug 2007
Location: Knoxville, TN
Posts: 2,949
Total Cats: 182
Aftermarket pistons
I tried to search but wasn't finding anything relavent. I was wondering if, on a healthy motor, it was reasonable/possible to install aftermarket pistons in a motor with no engine work? The most basic requirements for an aftermarket piston install so to speak.
Every build thread I see looks like the motor was bored, but I see that a few companies make 83mm pistons and was wondering if this was a reasonable option for a budget-ish built motor. If it is not advised, what would be required in order to properly install these stock sized pistons? Obviously rods, bearings, and gaskets would need to be changed as well, just curious specifically about the pistons mating to the block.
Every build thread I see looks like the motor was bored, but I see that a few companies make 83mm pistons and was wondering if this was a reasonable option for a budget-ish built motor. If it is not advised, what would be required in order to properly install these stock sized pistons? Obviously rods, bearings, and gaskets would need to be changed as well, just curious specifically about the pistons mating to the block.
#2
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
You must hone it at bare minimum, that's not optional. If the pistons you bought are the correct size to produce correct wall clearances with your motor, then you can drop them in with just a hone - that assumes the clearances are perfect within about .0005". (three zeros there.)
In reality, this is never the case, and you're going to be boring the motor. It's really not a big deal, it's like ~$200 at any competent machine shop - you're going to spend at least 8x that in seals, gaskets, bearings, rods, pistons, head gasket, valve guides and seals, etc.
In reality, this is never the case, and you're going to be boring the motor. It's really not a big deal, it's like ~$200 at any competent machine shop - you're going to spend at least 8x that in seals, gaskets, bearings, rods, pistons, head gasket, valve guides and seals, etc.
#3
Elite Member
Thread Starter
iTrader: (17)
Join Date: Aug 2007
Location: Knoxville, TN
Posts: 2,949
Total Cats: 182
Thanks for the info. I was kindof assuming that if everyone does it one way, that's probably the way it has to be done. Guess I've got to decide if I want to take that plunge or try to enjoy 200whp.
#5
Elite Member
Thread Starter
iTrader: (17)
Join Date: Aug 2007
Location: Knoxville, TN
Posts: 2,949
Total Cats: 182
^ I know, new rods will definitely go in. I was just unclear on what was required to do pistons as well. I really wish the NB motor was a 9:1 compression like the NA, I'd feel a lot better about just throwing rods in w/ stock pistons.
#6
You would be taking a risk in assuming the bore is true and the same size as stock after 1xx,xxx amount of miles. You're also assuming the pistons are exactly 83mm.
You might get lucky, but chances are you'll either get blowby, slap, or the skirts will collapse.
It's good insurance on what will probably be the cheapest part of your build to take it to a good machine shop.
Buy the pistons first and have them size the bores.
You might get lucky, but chances are you'll either get blowby, slap, or the skirts will collapse.
It's good insurance on what will probably be the cheapest part of your build to take it to a good machine shop.
Buy the pistons first and have them size the bores.
Thread
Thread Starter
Forum
Replies
Last Post
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM