Ballpark Prediction - NB1 motor + bolt ons/ecu
#21
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
There is no problem with using the stock AIT in any tube available (at zero boost of course). Just drill hole and use the grommet from the stock airbox.
Disregard the fact that my example was a quick hack to be able to race, it's not a tuned length at all, especially not for stock cams.
Disregard the fact that my example was a quick hack to be able to race, it's not a tuned length at all, especially not for stock cams.
#22
Ethanol burn formula:
C2H6O + 3O2 -> 2CO2 + 3H2O
Gasoline burn formula:
2C8H18 + 25O2 -> 16CO2 + 18H2O
Notice how the end product is the same - CO2 and H2O and Gasoline doesn't have any oxygen molecules.
#23
Place the iat anywhere that will put it in direct airflow of the intake charge. Doesn't matter where on the tube, though if its directly behind the radiators it might have a wee bit of heatsoak if you sit in traffic or idling too long.
I've done what Lars did and drilled the tube and just threaded it in before, didn't have issues. Since your intake has a port in it that should work if it fits. Wost case you can just stick it in the filter lol
Pretty sure he's talking about motor and not mani
I've done what Lars did and drilled the tube and just threaded it in before, didn't have issues. Since your intake has a port in it that should work if it fits. Wost case you can just stick it in the filter lol
Pretty sure he's talking about motor and not mani
#24
(Yes, H2O injection adds power, but it's not by giving you more oxygen to burn, it's by increasing effective octane and reducing the intake charge temperature)
--Ian
#27
I swapped out the stock engine out of my 97 for a 2003 NB2 engine last winter. With the NB2 engine, I added a RB header, full exhaust from Enthuza, gutted VTCS intake manifold, MS3X, and modified AEM intake. I also swapped in a 6spd transmission with lightweight flywheel and clutch kit from FM.
I am still working on the tune, but the overall results have been great so far. A 40whp jump when you start with 100whp transforms the car. It was definitely a worthwhile effort. The 97 is now a blast to drive with the new engine and supporting bolt on mods.
FYI... I placed the IAT sensor in the end of the air filter:
Grind down the rubber a bit to reduce the thickness
Drill a hole matching the OD of the threads on the IAT sensor
Cut a brass fitting down to make a NTP threaded nut
Insert IAT through end of the filter and use NTP nut to secure from the inside (don't line the nut being inside the intake tract, but with pipe threads I don't see it coming loose)
(The IAT approach only works if you have an open element air filter, but thought this might be useful information for someone.)
I am still working on the tune, but the overall results have been great so far. A 40whp jump when you start with 100whp transforms the car. It was definitely a worthwhile effort. The 97 is now a blast to drive with the new engine and supporting bolt on mods.
FYI... I placed the IAT sensor in the end of the air filter:
Grind down the rubber a bit to reduce the thickness
Drill a hole matching the OD of the threads on the IAT sensor
Cut a brass fitting down to make a NTP threaded nut
Insert IAT through end of the filter and use NTP nut to secure from the inside (don't line the nut being inside the intake tract, but with pipe threads I don't see it coming loose)
(The IAT approach only works if you have an open element air filter, but thought this might be useful information for someone.)
#28
Junior Member
Thread Starter
iTrader: (1)
Join Date: Sep 2009
Location: Skokie, IL
Posts: 213
Total Cats: 4
Good to know! Can't wait to get this thing in there. With the shape of the monsterflow intake filter, I'm not sure I'd be able to tap it in at the end, I may just tap into one of the openings along the crossover pipe.
With most of the parts added on to increase top end power (4-1 header, MSM cam, squaretop, intake), would there be any benefit to raise the stock redline to around 7500-8000? Would it even be safe at those rpms with the stock 99 motor?
What about a billet oil pump? Necessary for this application?
With most of the parts added on to increase top end power (4-1 header, MSM cam, squaretop, intake), would there be any benefit to raise the stock redline to around 7500-8000? Would it even be safe at those rpms with the stock 99 motor?
What about a billet oil pump? Necessary for this application?
I swapped out the stock engine out of my 97 for a 2003 NB2 engine last winter. With the NB2 engine, I added a RB header, full exhaust from Enthuza, gutted VTCS intake manifold, MS3X, and modified AEM intake. I also swapped in a 6spd transmission with lightweight flywheel and clutch kit from FM.
I am still working on the tune, but the overall results have been great so far. A 40whp jump when you start with 100whp transforms the car. It was definitely a worthwhile effort. The 97 is now a blast to drive with the new engine and supporting bolt on mods.
FYI... I placed the IAT sensor in the end of the air filter:
Grind down the rubber a bit to reduce the thickness
Drill a hole matching the OD of the threads on the IAT sensor
Cut a brass fitting down to make a NTP threaded nut
Insert IAT through end of the filter and use NTP nut to secure from the inside (don't line the nut being inside the intake tract, but with pipe threads I don't see it coming loose)
(The IAT approach only works if you have an open element air filter, but thought this might be useful information for someone.)
I am still working on the tune, but the overall results have been great so far. A 40whp jump when you start with 100whp transforms the car. It was definitely a worthwhile effort. The 97 is now a blast to drive with the new engine and supporting bolt on mods.
FYI... I placed the IAT sensor in the end of the air filter:
Grind down the rubber a bit to reduce the thickness
Drill a hole matching the OD of the threads on the IAT sensor
Cut a brass fitting down to make a NTP threaded nut
Insert IAT through end of the filter and use NTP nut to secure from the inside (don't line the nut being inside the intake tract, but with pipe threads I don't see it coming loose)
(The IAT approach only works if you have an open element air filter, but thought this might be useful information for someone.)
#31
Junior Member
Thread Starter
iTrader: (1)
Join Date: Sep 2009
Location: Skokie, IL
Posts: 213
Total Cats: 4
Hey everyone, just got tuned yesterday and wanted to give a quick update. The car was tuned on a Dynojet by a very highly regarded tuner in our area. He really tried to squeeze very last bit of power out of the setup, and we ended up with 130whp/115wtq:
The final modlist is as follows:
-99-00 NB motor, 47k miles, 180 psi dry across all four cylinders
-EUDM squaretop intake manifold
-MSM BP5A camshaft
-K&N 69-6000TP Intake
-Racing Beat header, wrapped
-RS*R Exmag GTII catback exhaust
-Exedy Stage 1 - 1.6 clutch
-XTD Prolite 9.5lb 1.6 flywheel
-MSPNP v1.1
-MAF delete, IAT sensor
-Hondata Intake Manifold Gasket
-93 octane
I'm very happy and instantly felt the difference in power. Car revs smooth and extremely quickly when paired with the 4:3 ring gear. With that said, there's something inside me that still wishes I was able to hit 140whp, especially since at this point, there's not much else I can do to net extra hp gains without taking apart the motor. For reference, he showed me some charts of spec miatas he's tuned and they were around 112-116whp on his dyno. Just curious if anyone might have an idea of what it could be missing, or is a dynojet just a low reading dyno? With such small power, 10whp is a pretty big difference.
ALSO - One issue we were having: is it normal for the idle on a 1st gen MSPNP to fluctuate a bit?
-With the lights off, the car idles around 1000-1200.
-When the lights turn on, the idle drops and begins to fluctuate from 700-1200, almost like the extra current draw brought the revs down to 700 and the engine is trying to compensate my quickly bringing it to 1200 before it drops again. At some points, the engine straight stalls.
He said its a minor issue that can easily be sorted out once I find a solution, and to possibly look into whether the MSPNP utilized an engine load control unit? He said it seems like it has to do with something like the MSPNP isn't signaling for the alternator to run harder to compensate for the increased load from turning on the headlights. Either way, even when setting base timing, we couldn't get the idle to remain completely steady at 850rpm, despite messing with the IAC screw and throttle cable.
Apologies for the long post. Thanks guys!
Lol crazy, you hit it right on the dot. Even the type of dyno! That's gotta deserve something.
The final modlist is as follows:
-99-00 NB motor, 47k miles, 180 psi dry across all four cylinders
-EUDM squaretop intake manifold
-MSM BP5A camshaft
-K&N 69-6000TP Intake
-Racing Beat header, wrapped
-RS*R Exmag GTII catback exhaust
-Exedy Stage 1 - 1.6 clutch
-XTD Prolite 9.5lb 1.6 flywheel
-MSPNP v1.1
-MAF delete, IAT sensor
-Hondata Intake Manifold Gasket
-93 octane
I'm very happy and instantly felt the difference in power. Car revs smooth and extremely quickly when paired with the 4:3 ring gear. With that said, there's something inside me that still wishes I was able to hit 140whp, especially since at this point, there's not much else I can do to net extra hp gains without taking apart the motor. For reference, he showed me some charts of spec miatas he's tuned and they were around 112-116whp on his dyno. Just curious if anyone might have an idea of what it could be missing, or is a dynojet just a low reading dyno? With such small power, 10whp is a pretty big difference.
ALSO - One issue we were having: is it normal for the idle on a 1st gen MSPNP to fluctuate a bit?
-With the lights off, the car idles around 1000-1200.
-When the lights turn on, the idle drops and begins to fluctuate from 700-1200, almost like the extra current draw brought the revs down to 700 and the engine is trying to compensate my quickly bringing it to 1200 before it drops again. At some points, the engine straight stalls.
He said its a minor issue that can easily be sorted out once I find a solution, and to possibly look into whether the MSPNP utilized an engine load control unit? He said it seems like it has to do with something like the MSPNP isn't signaling for the alternator to run harder to compensate for the increased load from turning on the headlights. Either way, even when setting base timing, we couldn't get the idle to remain completely steady at 850rpm, despite messing with the IAC screw and throttle cable.
Apologies for the long post. Thanks guys!
Lol crazy, you hit it right on the dot. Even the type of dyno! That's gotta deserve something.
#33
Junior Member
Thread Starter
iTrader: (1)
Join Date: Sep 2009
Location: Skokie, IL
Posts: 213
Total Cats: 4
E85 is available, but is not an option considering the car isn't properly setup for it. The values I was shooting for were based off Emilio's 95R' build, considering my bolt-on modlist is essentially identical:
https://www.miataturbo.net/general-m...project-63125/
Granted, he did have 10:5:1 pistons and a VVT NB2 motor, which likely attributed to his 145whp, but was only on 91 octane.
https://www.miataturbo.net/general-m...project-63125/
Granted, he did have 10:5:1 pistons and a VVT NB2 motor, which likely attributed to his 145whp, but was only on 91 octane.
#36
Elite Member
iTrader: (13)
Join Date: Dec 2006
Location: Taos, New mexico
Posts: 6,612
Total Cats: 567
Also, GREAT numbers imho. Congrats. Now tell us, how does it feel?
#37
Either the dyno reads very low or there is something else going on with the motor. I made 138 whp with a very similar set up on 91 octane without a square top and using a Jackson Racing header. If you swapped the newer motor into an older chassis you need to run the 94-97 alternator, I do not know those details of your set up though. Your power curve does not look like most of the square top manifold dyno's I've seen, you have a sharp drop off in the upper RPM. I run a VICS manifold and don't see a drop off that severe, here is an old chart from my motor for example;
#38
There's probably also some power available in the Adaptronic vs the MS1. If it's a stock 4-tooth trigger wheel then the timing isn't going to be as precise as the 12-1 wheel that Emilio's thread says he used.
--Ian
#39
A point and a half -- Emilio's car was 11.0:1, a stock NB1 motor is 9.5:1 (NB2 is 10.0:1).
There's probably also some power available in the Adaptronic vs the MS1. If it's a stock 4-tooth trigger wheel then the timing isn't going to be as precise as the 12-1 wheel that Emilio's thread says he used.
--Ian
There's probably also some power available in the Adaptronic vs the MS1. If it's a stock 4-tooth trigger wheel then the timing isn't going to be as precise as the 12-1 wheel that Emilio's thread says he used.
--Ian