Boost pressure and boost cut
#1
Elite Member
Thread Starter
iTrader: (17)
Join Date: Aug 2007
Location: Knoxville, TN
Posts: 2,949
Total Cats: 182
Boost pressure and boost cut
I wanted to get some input from you guys on where you have your boost cut set. I would like to run 12 pounds (~183kpa) of boost. I felt like I had that set pretty well, tuned at ambient temperatures around 75 degrees. When I datalogged I saw a spike to 189kpa but pressures seemed to hold right around 180-185kpa. I set boost cut to 200kpa, which I figured would give me a little leeway but still be safe enough if I did jump that high. The trouble is when it's cooler out, even 65 degrees out, I'm getting a little boost cut at higher rpms. Conversely, when it gets up to 85 degrees I'm loosing a little boost.
Also, should I be seeing this much variance in pressure when the temperature fluctuates (talking about the difference in 11.5 and 14.5psi w/ a 20 degree ambient fluctuation)?
Finally, if that much fluctuation in manifold pressure is common, what do you consider "the boost you're running" to be? For example, hypothetically on a very cold day I peak 15psi and I consistently hold 14psi, on a normal day I peak 13psi and consistently hold 12psi, then on a hot day I peak 11psi and consistently hold 10psi. What would you personally consider boost I'm running to be? I realize this may sound like a stupid question, but I think most would agree here that 10psi on a stock motor is fairly safe, while 15psi on a stock motor is pushing the limits, I'd just like to clarify how "xx psi" is being defined. So I can tune accordingly.
Thanks for the help. I appreciate you guys baring with my stupid questions.
*Mods, if this isn't the right forum, I apologize and feel free to move it, I wasn't sure where it should go*
Also, should I be seeing this much variance in pressure when the temperature fluctuates (talking about the difference in 11.5 and 14.5psi w/ a 20 degree ambient fluctuation)?
Finally, if that much fluctuation in manifold pressure is common, what do you consider "the boost you're running" to be? For example, hypothetically on a very cold day I peak 15psi and I consistently hold 14psi, on a normal day I peak 13psi and consistently hold 12psi, then on a hot day I peak 11psi and consistently hold 10psi. What would you personally consider boost I'm running to be? I realize this may sound like a stupid question, but I think most would agree here that 10psi on a stock motor is fairly safe, while 15psi on a stock motor is pushing the limits, I'd just like to clarify how "xx psi" is being defined. So I can tune accordingly.
Thanks for the help. I appreciate you guys baring with my stupid questions.
*Mods, if this isn't the right forum, I apologize and feel free to move it, I wasn't sure where it should go*
#3
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
Get rid of your MS-controlled EBC and get a simple MBC. It brings the temp variances to like 1psi, instead of 3-4. Open-loop EBC is crap.
I used to aim for 15psi, overshoots to 16.5, had the overboost cut at 17.5psi.
I used to aim for 15psi, overshoots to 16.5, had the overboost cut at 17.5psi.
#4
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
on my vw's I loved EBC because it was a highway car. Its nice to have the slower response with the MBC, its more predictable and easier to drive on the track. If you're just a streetracer though, it you'll probably like the EBC.
#5
I gave up on the EBC and went back to the MBC. I have the MBC set for 189 and I have boost cut set at 198, but it is tuned up there. I don't want to go higher than 14psi. I retarded the timing and added fuel to the cells from 198 to 212. In case the MBC and the boost cut fails, unlikely, then I am covered. 16psi is ridiculous, and I don't need a DD street car with that much power. There is no place in the city to exploit its potential.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM