Need Help ms3x - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


Engine Performance This section is for discussion on all engine building related questions.
Sponsored by:
Sponsored by:

Reply
 
 
 
LinkBack Thread Tools Search this Thread
Old 07-13-2018, 01:34 AM   #1  
Newb
Thread Starter
 
Join Date: May 2018
Posts: 4
Total Cats: 0
Default Need Help ms3x

ok so, first post after lurking forever ( a good year or so since I've been interested in turbocharging my Miata) I've tried reading a lot and I mean a LOTand honestly I'm not afraid doing many things on my own. so I finally decided about a month ago to go with a ms3x and following brain's guide on trubokitty.com (though I put in all the components in the mainboard... it was fun lol and I really didn't have much to do anyway) and today I decided to make a custom intake with some of the intercooler piping I have and I modified to be able to connect the iac valve and a gm iat sensor. I loaded in the firmware and brain's base map and all I got was the engine turning over but stalling after a really short while. I took off the "stsign" fuse and put in a wideband O2 sensor (AEM 30-4110) ran the vacuum line from the FPR to the ms3x and boost gauge I have installed (though not boosting until I can get ms to run fine without boost) any help would be appreciated . this is what tunerstudio looks like right now on the cluster. not connected to the car though it's connected to a custom power supply for it though tps was the same when it was and I did disconnect it. planning to use a wells tps later
Attached Thumbnails
Need Help ms3x-tune.png  
fam4 is offline   Reply With Quote
Old 07-13-2018, 04:21 AM   #2  
Newb
Thread Starter
 
Join Date: May 2018
Posts: 4
Total Cats: 0
Default

Guess it would help to say it's a federal 1993 1.6
fam4 is offline   Reply With Quote
Old 07-14-2018, 01:58 PM   #3  
Newb
 
Join Date: Feb 2018
Location: Knoxville, TN
Posts: 34
Total Cats: 5
Default

If/when someone more knowledgeable than me tries to help you, they'll more than likely ask for a copy of your .msq and a log of you trying to start the car. That's all the help I can offer, sadly. I hope you get it resolved.
Artifex is offline   Reply With Quote
Old 07-14-2018, 03:14 PM   #4  
Junior Member
 
Join Date: Apr 2017
Location: South Dakota
Posts: 254
Total Cats: 17
Default

Your post is incomprehensible. I'm not even sure what you're asking.

Are you saying the car cranks, starts, then dies? If so you need to tune it.
SpartanSV is online now   Reply With Quote
Old 07-14-2018, 04:07 PM   #5  
Newb
Thread Starter
 
Join Date: May 2018
Posts: 4
Total Cats: 0
Default

well the msq is the one braineck has on trubokitty. maybe my timing was incorrect mechanically so that's is what ill check next and yes it cranks and dies.. slowly... in about 5 seconds
fam4 is offline   Reply With Quote
Old 07-14-2018, 07:39 PM   #6  
Junior Member
 
Join Date: Apr 2017
Location: South Dakota
Posts: 254
Total Cats: 17
Default

Quote:
Originally Posted by fam4 View Post
well the msq is the one braineck has on trubokitty. maybe my timing was incorrect mechanically so that's is what ill check next and yes it cranks and dies.. slowly... in about 5 seconds
Recheck your settings. Base timing, all of your sensor settings, injector settings if you aren't stock.

If everything checks out then tune the car.
SpartanSV is online now   Reply With Quote
Old 07-14-2018, 09:46 PM   #7  
Newb
Thread Starter
 
Join Date: May 2018
Posts: 4
Total Cats: 0
Default

Everything is stock right now again. I checked the timing and it was off by 2 degrees I really hope this works! though would timing really affect it to that degree?

Last edited by fam4; 07-15-2018 at 02:20 AM.
fam4 is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
need help with 96 and MS3X, no start issue loveSONG769 MEGAsquirt 13 04-04-2018 11:03 AM
Bought a Miata MS3/MS3x kit to use on a 240sx, know if I need to change anything? MostHated MEGAsquirt 0 03-01-2016 07:04 PM
MS3 w/o MS3x crank and ignition signal issue and MS3x question wolfblind MEGAsquirt 10 01-18-2015 03:42 AM
help! MS3x 1990 NO spark on cyl 2 and 3 nwNAMiata MEGAsquirt 2 08-07-2012 06:05 PM
MS3 & MS3X - 99% Ready to install. Help me ensure I don't screw up. stucky MEGAsquirt 10 02-26-2012 12:28 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 03:51 AM.




We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.