Miata Turbo Forum - Boost cars, acquire cats.
Andy's Table Spanning only to 18 psi (my upper limit) Compare to the next picture, which is my table Interpolated with the same rows and columns as this one (cell to cell correlation).
Andy's Table Spanning only to 18 psi (my upper limit) Compare to the next picture, which is my table Interpolated with the same rows and columns as this one (cell to cell correlation).
0 2021/08/24 17:18:12
My Table to my upper values, but with Andy's interpolation rows and columns.
My Table to my upper values, but with Andy's interpolation rows and columns.
0 2021/08/24 17:18:20
0 2021/09/11 05:33:53
0 2021/11/06 10:15:35
What you have, which seems to have the Baro directly in the fueling equation.
What you have, which seems to have the Baro directly in the fueling equation.
0 2022/01/19 07:44:44
I'm not sure about this, as the instructions do not mention the "Fixed" setting.
I'm not sure about this, as the instructions do not mention the "Fixed" setting.
0 2022/01/19 07:44:47
0 2018/03/29 13:52:45
0 2022/04/16 15:30:33
0 2022/07/29 14:59:26
Intercooler does not leak
Intercooler does not leak
0 2018/04/11 17:12:43
0 2022/08/09 09:42:24
How to plow with a Miata
How to plow with a Miata
0 2018/04/11 17:12:44
0 2022/09/04 14:34:52
Ducting may need replacing. Definitely repaired.
Ducting may need replacing. Definitely repaired.
0 2018/04/11 17:12:45
0 2022/09/12 14:36:31
A/C still works
A/C still works
0 2018/04/11 17:12:46
Oil Cooler flange a little bent, but OK
Oil Cooler flange a little bent, but OK
0 2018/04/11 17:12:48
0 2022/10/10 11:24:24
P/S cooler
P/S cooler
0 2018/04/11 17:12:48
0 2022/10/29 17:22:37
0 2022/10/29 17:22:48
Close to disastrous
Close to disastrous
0 2018/04/11 17:12:50
Intercooler was vertical
Intercooler was vertical
0 2018/04/11 17:12:51
0 2022/12/15 06:49:24
Superficial sheet metal bent
Superficial sheet metal bent
0 2018/04/11 17:12:52
0 2023/01/07 16:32:28
0 2018/04/11 17:12:53
0 2023/01/31 04:51:50
0 2023/05/18 13:16:59
0 2018/04/11 17:12:54
Where I put the un-needed relay
Where I put the un-needed relay
0 2023/05/18 13:18:03
0 2018/05/12 12:36:18
0 2023/05/18 13:18:05
0 2018/05/15 18:12:11
0 2018/05/27 13:55:55
Windings and shaft removed, not drilled out yet. I filled the cavity and glued the 2 bobbin halves back together with Ultem Hot Melt, before drilling.
Windings and shaft removed, not drilled out yet. I filled the cavity and glued the 2 bobbin halves back together with Ultem Hot Melt, before drilling.
0 2023/05/18 13:18:07
0 2018/05/30 09:08:33
Oil Pressure Present
Oil Pressure Present
0 2023/05/18 13:52:25
No Oil Pressure Present
No Oil Pressure Present
0 2023/05/18 13:52:27
0 2018/06/05 02:56:49