Miata Turbo Forum - Boost cars, acquire cats.
I went ahead and drilled and tapped the hole.
I went ahead and drilled and tapped the hole.
0 2025/08/29 22:01:17
I’ll share the measurements tomorrow, but by my calculations, this area is in the fluid, clear of the shift mechanisms, and leaves room for a wrench on the sensor
I’ll share the measurements tomorrow, but by my calculations, this area is in the fluid, clear of the shift mechanisms, and leaves room for a wrench on the sensor
0 2025/08/29 22:01:14
I believe that as long as the sensor is to the rear of this notch in the 6th gear shift fork (rear being “above” in this photo) it won’t interfere with the rod.
I believe that as long as the sensor is to the rear of this notch in the 6th gear shift fork (rear being “above” in this photo) it won’t interfere with the rod.
0 2025/08/29 22:01:10
My 3D thinking says this is about the right place for the Ballenger sensor. It’s definitely in the fluid, yet should clear both the shift fork and whatever that other rod is. In theory. I will check this tomorrow after reassembly.
My 3D thinking says this is about the right place for the Ballenger sensor. It’s definitely in the fluid, yet should clear both the shift fork and whatever that other rod is. In theory. I will check this tomorrow after reassembly.
0 2025/08/29 22:01:07
This is the area I’m targeting. That’s the sixth gear what’sy doo dad, and the rod sticking up through the casting is the whoosy-do.
This is the area I’m targeting. That’s the sixth gear what’sy doo dad, and the rod sticking up through the casting is the whoosy-do.
0 2025/08/29 22:01:04
Remove this M8 bolt to the rear of that sensor you removed, before you attempt to separate the case.
Remove this M8 bolt to the rear of that sensor you removed, before you attempt to separate the case.
0 2025/08/29 21:55:07
Remove the upper half of the shift box and then remove the bolt holding the shift cup to the shaft (12mm head)
Remove the upper half of the shift box and then remove the bolt holding the shift cup to the shaft (12mm head)
0 2025/08/29 21:55:04
Remove this sensor. Whichever it is.
Remove this sensor. Whichever it is.
0 2025/08/29 21:55:01
Remove these M8 bolts (12mm head)
Remove these M8 bolts (12mm head)
0 2025/08/29 21:54:58
Remove the speedometer sensor.
Remove the speedometer sensor.
0 2025/08/29 21:54:54
0 2025/08/27 13:32:52
0 2025/08/27 13:32:03
0 2025/08/27 13:03:07
0 2025/08/27 13:03:05
0 2025/08/24 21:42:36
0 2025/08/17 22:34:13
0 2025/08/17 22:34:10
0 2025/08/17 00:18:37
0 2025/08/17 00:09:19
0 2025/08/17 00:06:12
0 2025/08/17 00:06:09
0 2025/08/12 09:55:35
0 2025/08/12 09:52:50
0 2025/08/06 20:41:24
0 2025/08/05 10:01:23
0 2025/07/28 14:03:56
0 2025/07/28 14:03:54
0 2025/07/28 14:03:53
0 2025/07/28 14:03:51
0 2025/07/28 14:03:44
0 2025/07/28 14:03:25
0 2025/07/28 14:03:18
0 2025/07/28 14:03:16
0 2025/07/21 10:52:01
0 2025/07/14 13:31:24
0 2025/07/14 09:28:02
0 2025/07/14 09:28:00
0 2025/07/14 09:27:59
0 2025/07/14 09:27:58
0 2025/07/14 09:27:57