How to paint your wheels
#41
Sorry about the necroposting, but this thread is what my question is based on.
Getting ready to paint my WRX's wheels, and am following the guidlines leatherface started. I'm in the cleaning stage, how clean is clean? Best way to remove the grease in the lug holes. And do I need to remove the balancing weights?
Getting ready to paint my WRX's wheels, and am following the guidlines leatherface started. I'm in the cleaning stage, how clean is clean? Best way to remove the grease in the lug holes. And do I need to remove the balancing weights?
#43
Oh yeah, I'm definitely going to get those holes. I hadn't done that wheel yet, the one I did do still had a little gunk in it even though I was using a detail brush and dawn soap. I guess I'm wondering if I can use something harsher, like brake cleaner, in there.
The picture with the back side of the wheel showing the weights has been scrubbed, is that clean enough?
The picture with the back side of the wheel showing the weights has been scrubbed, is that clean enough?
#44
Want fries with that?
iTrader: (3)
Join Date: Oct 2009
Location: Twin Cities, Minnesota
Posts: 2,011
Total Cats: 2
Anyone ever restored a set of BBS RA's? I've got a set sitting in my garage, I've got the color scheme all planned out (Mild gold interior with polished lip) but they are dirty as **** and a BITCH to clean, as you can imagine would be the result of having bunches of tiny little holes.
How effective is that paint stripper? This dirt is melded on, I had to take a dremel to it to get it off of just one part. Would it be powerful enough to get off after a couple of coats and whippings/sprayings?
How effective is that paint stripper? This dirt is melded on, I had to take a dremel to it to get it off of just one part. Would it be powerful enough to get off after a couple of coats and whippings/sprayings?
#47
Ok, I cleaned up the wheels pretty good, followed leatherface's instructions and all was going really well.That is until like an idiot I kept spraying when the spray can started to splatter on the color coat. I didn't notice at first, but it left a light spatter on parts of the wheel. It looks good from 5' but when you get down on it you can see the crappy job.
It's been 4 days now and I'm ready to fix it, do I
1) just put another coat or two on, then clear coat, and call it good?
2) sand a bit off and follow step 1?
3) strip and start over?
I'm in the garage ready to work so quick reply is appreciated.
It's been 4 days now and I'm ready to fix it, do I
1) just put another coat or two on, then clear coat, and call it good?
2) sand a bit off and follow step 1?
3) strip and start over?
I'm in the garage ready to work so quick reply is appreciated.
#50
Elite Member
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
How well do all of these paints hold up to brake dust? My 6ULs look like **** thanks to brake dust washing neglect and I don't want to take the time to paint them if they will **** up right quick again.
#55
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Thanks for making this thread Jarrod. I followed the procedure you outlined and the results were pretty good.
Here's what I required:
Aircraft Stripper x 3 cans (home depot)
Duplicolor Adhesion Promoter x 1 can (o'reily's)
Rustoleium Fast Dry Sandable Primer x 1 can (home depot)
Duplicolor High Performance Wheel Paint x 3 cans (o'reily's)
Duplicolor High Performance Wheel Clear x 2 cans (o'reily's)
400 grit sand paper x 1 sheet (home depot)
scotch brite pads x 2 pads (home depot)
spray paint can sprayer holder thingie (home depot)
note cards, small x 2 packs of 100 (walmart)
note cards, large x 1 pack of 100 (walmart)
masking tape (walmart)
Total Cost: Appx $75 (plus I'll need to get them rebalanced)
Labor: All day
Result:
Hard to get a good picture since they're metallic and the sun is up high, so it washes out. I'm sure the camera can take a better picture if the operator were competent enough to take it out of automatic. What looks like overspray on the tire isn't.
Overall, this is not something I'd do to a set of new looking wheels to simply change color, as laying paint down out of cans in the driveway leaves something to be desired, however it's a very good procedure to clean up wheels that are getting long in the tooth.
I have them "baking" in the driveway now. I'll give them a few days then take them for a balance before putting them on the car. But they'll look pretty good.
Here's what I required:
Aircraft Stripper x 3 cans (home depot)
Duplicolor Adhesion Promoter x 1 can (o'reily's)
Rustoleium Fast Dry Sandable Primer x 1 can (home depot)
Duplicolor High Performance Wheel Paint x 3 cans (o'reily's)
Duplicolor High Performance Wheel Clear x 2 cans (o'reily's)
400 grit sand paper x 1 sheet (home depot)
scotch brite pads x 2 pads (home depot)
spray paint can sprayer holder thingie (home depot)
note cards, small x 2 packs of 100 (walmart)
note cards, large x 1 pack of 100 (walmart)
masking tape (walmart)
Total Cost: Appx $75 (plus I'll need to get them rebalanced)
Labor: All day
Result:
Hard to get a good picture since they're metallic and the sun is up high, so it washes out. I'm sure the camera can take a better picture if the operator were competent enough to take it out of automatic. What looks like overspray on the tire isn't.
Overall, this is not something I'd do to a set of new looking wheels to simply change color, as laying paint down out of cans in the driveway leaves something to be desired, however it's a very good procedure to clean up wheels that are getting long in the tooth.
I have them "baking" in the driveway now. I'll give them a few days then take them for a balance before putting them on the car. But they'll look pretty good.
__________________
91 Turbo | 10AE Turbo | 01 Track Rat | #323 Mazda Champcar
Chief of Floor Sweeping, DIYAutoTune.com & AMP EFI
Crew Chief, Car Owner & Least Valuable Driver, HongNorrthRacing
Last edited by Ben; 07-05-2010 at 01:39 PM.
#58
Looked for this thread and I'm already discouraged at the work involved to revive old wheels. I've got 3 scuffed and scratched up Pro Race 1's and 1 brand new Pro Race 1...trying to decide if I want to refinish the used wheels to match the new one, refinish all four in a matching (possibly new) color, or just say "screw it" and let the brake dust cover up the scuffs and scratches over time.
#59
Looked for this thread and I'm already discouraged at the work involved to revive old wheels. I've got 3 scuffed and scratched up Pro Race 1's and 1 brand new Pro Race 1...trying to decide if I want to refinish the used wheels to match the new one, refinish all four in a matching (possibly new) color, or just say "screw it" and let the brake dust cover up the scuffs and scratches over time.