Thoughts on towing a Miata
#1
Boost Pope
Thread Starter
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
Thoughts on towing a Miata
So I'm getting ready to head out cross-country on Thursday. I've got a 16' Penske truck and a four wheel car trailer reserved. Thing is- I couldn't get Penske's online reservation thing to accept a Miata (of any year) on the towing selector, so I lied and said I had a Pontiac Solstice.
Given this, and the fact that my car is slightly lowered, I have some concerns. If it turns out to be unable to mount the four wheel trailer, I may have to use the two-wheel car dolly. (Yes, I know about the blocks of wood trick, etc)
Question is- say I tow it the five miles from Penske to my house on this contraption, then remove the driveshaft and pull it the 2,500 miles to NC. Apart from the fact that my RE-01Rs won't be too happy about this, any thoughts as to the drivetrain itself? There won't be much load on the diff, I'm just curious as to how the R&P gear might feel about this.
Given this, and the fact that my car is slightly lowered, I have some concerns. If it turns out to be unable to mount the four wheel trailer, I may have to use the two-wheel car dolly. (Yes, I know about the blocks of wood trick, etc)
Question is- say I tow it the five miles from Penske to my house on this contraption, then remove the driveshaft and pull it the 2,500 miles to NC. Apart from the fact that my RE-01Rs won't be too happy about this, any thoughts as to the drivetrain itself? There won't be much load on the diff, I'm just curious as to how the R&P gear might feel about this.
#5
I towed my Miata to Summit Pt a few wks ago on H&R race springs. The car is lowered quite a bit. I would guess-timate at least an inch or two. I used a u-haul 4 wheel trailer. My car is on RA1's so the tire height is close to stock.
The problem I had with the UH trailer was that it had some metal edges that ran the length up the trailer in the center section. These metal plates were about 2 inches long and pointed up at a 20 degree angle. When the car was placed on the trailer the plates pointed directly at the frame rails. I would have to be very careful during loading to not skid the frame rails on the protruding edges. With a spotter...it wasn't very hard. The car also ran up on the trailer without blocks. I think the short nose helped a lot in that respect.
After loading the car and chaining it down the towing wasn't a problem.
The problem I had with the UH trailer was that it had some metal edges that ran the length up the trailer in the center section. These metal plates were about 2 inches long and pointed up at a 20 degree angle. When the car was placed on the trailer the plates pointed directly at the frame rails. I would have to be very careful during loading to not skid the frame rails on the protruding edges. With a spotter...it wasn't very hard. The car also ran up on the trailer without blocks. I think the short nose helped a lot in that respect.
After loading the car and chaining it down the towing wasn't a problem.
#6
Boost Pope
Thread Starter
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
No *****? The directions on their towing pamphlet rather strictly caution against this. Then again, they tell you not to reverse the truck with the trailer on it, which I assume is due to people not knowing how to properly reverse a trailer. Of course, what I do with it after I leave their lot is my business... You leave the steering column locked, I assume?
I'm really hoping the car carrier works out. I've used it before (carrying my Integra from OH to CA) and despite being longer & heavier, I find it relatively easy to maneuver given its very short wheelbase and the greater distance from the tongue to the axles.
I'm really hoping the car carrier works out. I've used it before (carrying my Integra from OH to CA) and despite being longer & heavier, I find it relatively easy to maneuver given its very short wheelbase and the greater distance from the tongue to the axles.
#7
A set of ramps ( be sure they are sturdy before you back a loaded truck onto them) under the rear wheels of the truck will make loading the miata on the trailer much easier.
I would be concerned about dragging whichever end is not on the dolly as you enter and exit places.
My vote is the trailer.
I would be concerned about dragging whichever end is not on the dolly as you enter and exit places.
My vote is the trailer.
#8
You can reverse with a trailer no prob (as long as you know how to reverse a truck with a trailer). Just do NOT reverse with a car on the dolly. Too many pivot points. It will not behave!
\
/
\
It will do that^ and possibly jam the dolly into your car.
I drove across the country with one, and nearly got stuck having to dismount the car from the dolly when I pulled into a hotel parking lot that from the street looked like it wrapped around the whole building. Luckily, it was 6 degrees out, so I had no problem driving a fully loaded uHaul with car dolly over some grass to an adjoining lot.
\
/
\
It will do that^ and possibly jam the dolly into your car.
I drove across the country with one, and nearly got stuck having to dismount the car from the dolly when I pulled into a hotel parking lot that from the street looked like it wrapped around the whole building. Luckily, it was 6 degrees out, so I had no problem driving a fully loaded uHaul with car dolly over some grass to an adjoining lot.
#9
Elite Member
iTrader: (21)
Join Date: Jun 2007
Location: Rochester, NY
Posts: 6,597
Total Cats: 1,263
I got mine on the U-Haul trailer, no problem. If it's lowered, you're gonna have to use the same steps you'd take to get it up on a set of ramps (lay down stacks of 2x6), but it will sit on the trailer fine.
I towed mine with a Jeep, and the trailer was heavier than the Miata.
I towed mine with a Jeep, and the trailer was heavier than the Miata.
#10
I towed a lowered (2" drop IIRC) parts car with a Uhaul 4 wheel trailer, no issues, needed a spotter but it drove up just fine.
I personally would not make such a big trek with a dolly.
lol, and as rleete said, the trailer was heavier then the miata. It was pulled (100 miles?) by a F150, no issues.
I personally would not make such a big trek with a dolly.
lol, and as rleete said, the trailer was heavier then the miata. It was pulled (100 miles?) by a F150, no issues.
#12
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Then again, they tell you not to reverse the truck with the trailer on it, which I assume is due to people not knowing how to properly reverse a trailer. Of course, what I do with it after I leave their lot is my business... You leave the steering column locked, I assume?
Center the steering wheel and tie it to the roll bar.
I'm really hoping the car carrier works out. I've used it before (carrying my Integra from OH to CA) and despite being longer & heavier, I find it relatively easy to maneuver given its very short wheelbase and the greater distance from the tongue to the axles.
#13
I'm Miserable!
iTrader: (5)
Join Date: Dec 2006
Location: jacksonville, fl
Posts: 1,711
Total Cats: -1
in a manual trans car, the drive wheels can be on the ground and trans in nuetral and you can tow it with no problems at all. also, if you tow it with the front wheels on the ground TIE OFF THE STEERING WHEEL, i can not express how important that is. the steering lock should be enough, but they can and will brake. just take your seatbelt and pull it all the way out, loop it through the bottom of the steering wheel then hook it up.
#15
Boost Pope
Thread Starter
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
Ok, lots of opinions...
I don't think my plastic ramps will accommodate a truck with a GVWR of 10,000 lbs, but perhaps terrain can be made to work to my advantage.
I'll stop by Lowe's on the way there and pick up some 2x6 sections- probably get two 6' lengths and have em cut to 2.5' and 3.5' there at the store.
I really want to avoid the dolly if possible.
I don't think my plastic ramps will accommodate a truck with a GVWR of 10,000 lbs, but perhaps terrain can be made to work to my advantage.
I'll stop by Lowe's on the way there and pick up some 2x6 sections- probably get two 6' lengths and have em cut to 2.5' and 3.5' there at the store.
I really want to avoid the dolly if possible.
#17
Elite Member
iTrader: (21)
Join Date: Jun 2006
Location: Point Pleasant, NJ
Posts: 2,957
Total Cats: 2
I picked up a lowered 97M(fm springs) with a U-haul trailer. Had no trouble getting it onto the trailer. Well other than having to push it up since the car didn't run.
According to the 1994 Owners manual:
"A towed vehicle usually should have its rear wheels off the ground. If excessive damage or other conditions prevent this, use wheel dollies."
According to the 1994 Owners manual:
"A towed vehicle usually should have its rear wheels off the ground. If excessive damage or other conditions prevent this, use wheel dollies."
#20
You can't back a dolly at all. It's way too close to the back of the vehicle to control.
Otherwise, I agree with the people. If you've gotta do a tow dolly, put the front wheels on the ground. Otherwise, trailer is the way to go.
I learned with my M3 that I could go up stuff like rollback tow trucks backwards but could not forwards because the bumper would get smashed. Your mileage may vary but give it a shot.
Otherwise, I agree with the people. If you've gotta do a tow dolly, put the front wheels on the ground. Otherwise, trailer is the way to go.
I learned with my M3 that I could go up stuff like rollback tow trucks backwards but could not forwards because the bumper would get smashed. Your mileage may vary but give it a shot.