My rusty AutoX toy
4 Attachment(s)
Hey everyone,
I purchased a white 1991 Miata back in February with 142,000 miles for $150. All it needed was a new battery and a 80amp fuse to get it running. Since then I have been competing in autocross events with it, in the Maryland area. I inevitable ran into Soviet at a couple of these events. This conjured up some quite expensive ideas. I plan to have the car turbo'ed by the spring of 2013. I plan to run with the 1.6, I may do internals on it, unless I am talked out of it. I want to run megasquirt, and I feel that this needs to be my first step toward awesomeness. I will be starting a build thread in the near future. Oh yeah here is a picture of the Bucket Thanks For Looking [IMG]https://www.miataturbo.net/attachmen...ine=1345739677[/IMG] [IMG]https://www.miataturbo.net/attachmen...ine=1345739677[/IMG] |
Welcome! Sweet deal only $150!!
|
Thanks for joining, BThomas220!
|
Wow, that's one heck of a deal for $150. Welcome!
|
Sounds good. Cut out that rust before it spreads though, even if you dont fix it right away.
|
Hello!
If you want to stay cheap, I have a pair of megasquirt 2 |
If you are seriously considering doing internals on a motor there is absolutely no reason not to build a 1.8 instead of the 1.6.
Which clubs are you autoxing with up there? |
Awesome deal for $150
|
Originally Posted by shuiend
(Post 919182)
Which clubs are you autoxing with up there?
sounds like CDC if he met up with Soviet. and I agree. Buy a 1.8L and build that, then swap it in. 1.6Ls should be melted for scrap. |
Thanks for the replies
Originally Posted by soviet
(Post 919179)
Hello!
If you want to stay cheap, I have a pair of megasquirt 2 Pm me.
Originally Posted by shuiend
(Post 919182)
If you are seriously considering doing internals on a motor there is absolutely no reason not to build a 1.8 instead of the 1.6.
Which clubs are you autoxing with up there?
Originally Posted by Braineack
(Post 919190)
sounds like CDC if he met up with Soviet. and I agree. Buy a 1.8L and build that, then swap it in. 1.6Ls should be melted for scrap.
|
Originally Posted by BThomas220
(Post 919256)
Don't you have a 1.6L :brain:
|
All glory to the 1.8L.
|
I can't think of any more fun you can have for $150.00, nice find!
|
1.6 glory. BP is for fagtards
OP, nice car. I would love a beater miata for auto-x only. |
Originally Posted by BThomas220
(Post 919256)
I really was leaning toward MS3 but if the price is right...
|
The "x" means expander card, which is just a $90 module with pre-built circuits on it. But I agree, get the expander.
I can build you a MS3x PNP for exactly 4.6 times what you paid for your car. |
not a bad way to spend 150$, nice welcome
|
Brainy, I will probably be in touch with you about getting a MS3X built. I would like to get one running on the car while it has the 1.6 in it. Is there much involved with changing the ecu and tuning when I switch to a 1.8, or is it pretty trivial?
|
like one parameter in the software.
|
It really depends on how you go around your 1.8 swap. you can do it the lame, peon way and just use all 1.6 wiring harness, sensors, 1.6 ingiton and throttle body. Doing it this way is easy but... lame - No sequential unless you rewire your harness, poor timing accuracy, lame ingitor, tach signal comes from coils, etc etc etc.
Or, you can do it the right way and use a crank sensor, NB throttle body and NB knock sensor (or any other knock sensor). It's more involved but is superior. Either way, all you would need to do is change configuration in tuner studio and wiring. You don't need to mod the MS3 in any way or form (other than add-on knock board). |
All times are GMT -4. The time now is 06:56 PM. |
© 2024 MH Sub I, LLC dba Internet Brands