18 psi with no FMIC
1 Attachment(s)
I don't have my pump pressure on the WI set up to keep it stable though. So until i get to realy tunning it i will back it off to good ole 14 psi. here is the MLV for any who are interested.
To recap fleabay manifolds ceramic caoted MHI small 16g Parker store lines Ebay knock off BOV MS1 running fuel LC1 WB 02 act Xtreme PP 4 puck unsprung disk Vodoo MBC with ace hardware spring Snow performance WI with cooling mist nozzle on a selonoid for stage 2 for a total of about 7 gph. High impedance 542 cc/min injectors flowed and test by witchhunter performance. feeling 18 psi priceless. |
Ok i have donned my flame suit lets see what happens
|
aren't you running stock rods?
|
yes with weisco 40 over pistons
|
does me no good when you intake temps so 25° flat throughout! Wanna fix that and try again?!
and i swear you made me believe that turbo spooled faster than my t3...guess it wasnt the case. |
Originally Posted by Braineack
(Post 148828)
does me no good when you intake temps so 25° flat throughout! Wanna fix that and try again?!
and i swear you made me believe that turbo spooled faster than my t3...guess it wasnt the case. |
he needs to fix his CLT temp sensor too.
|
AIT is ambient under hood temps, CLT is accurate i gues i dunno i think adam got that one right. I run a 170 or so degree thermostat at like 80% water with no FMshitercooler. I would realy like a oil cooler though so i can keep the water temps around 140 or so degrees and the oil at 190-210 max.
|
take it to the track!
|
Originally Posted by magnamx-5
(Post 148868)
AIT is ambient under hood temps, CLT is accurate i gues i dunno i think adam got that one right. I run a 170 or so degree thermostat at like 80% water with no FMshitercooler. I would realy like a oil cooler though so i can keep the water temps around 140 or so degrees and the oil at 190-210 max.
there's no way your water is cruising at 150°F. Betcha $10 your R7 resistor is still install is fubaring the readings. All you gotta do to confirm is idle untill the fans kick on. if they come on anythign less than 200°F (93C), you know it's not reading right. your intake temps dont move whatsoever. if you run WI at 5psi like you say, then I'd expect a small bump in temps at the onset of boost. your intake temps barely move that entire log. can you go out and take a 3rd gear pull from 2000RPM to redline and then stop it? |
2 Attachment(s)
My AIT is over by the Brake master cylinder of course it didn't go up yes i can ill be back in a minute. As a mater of fact here it is the MLV and a capture I fired the car up and went down the raod and back.
Attachment 215885 |
Brain, he's trying to say his AIT sensor is not reading the temp inside the charge pipe, but is laying loose under the hood.
|
1 Attachment(s)
Yes i am Koto here is my GM ait sensor I never claimed to have it anywhere in the intake air flow.
|
:gtfo: :nono: :td: :greddy2: :inout: |
me = speechless
|
????? :dunno: So i eased up towards 5K he wanted to see the spool if you look at the log it get positive boost of .4 psi by 1400 rpm at 1 point.
|
Why is your AIT sensor sitting in the engine bay?
|
god damn you richard. fix that shit you ghetto mfer.
|
ummmmmmmmmmmmmmmmmmm brokes!
1. your car is running a little cold. 140F? brr. should be like 190F. the sun heating the interior of your car is 140F. fix that sensor. 2. how do you know if WI is better than an IC if you dont actually measure your intake temps?? fix that sensor too. |
but tapping the manifold is to hard. and tapping the crossover gets me nothing. Just suffice it to say 17-18 psi on stock timming with minor oil pressure gauge detonation if i stay in it to long. i am sure that by tunning my pump pressure abit more or tunning it on the dyno i can do better. But i also have to fix my fuel wich for some reason is close to 12-1 through most of the range wich it should be a little higher to help me spool abit. But for a raod tune on stock spark maps i think it is pretty damn sweet. Maybe this winter when i have chad or someone help me with my spark and EBC i will have them check the rest of the unit. But doesn't MS control fans as well. I coulda swore mine was set to come on at 170 F
|
All times are GMT -4. The time now is 04:46 PM. |
© 2024 MH Sub I, LLC dba Internet Brands