RevMS2v3 engine running erratically. Was perfect 2 days ago. AFR/RPMS/MAF all over!
#1
Junior Member
Thread Starter
iTrader: (5)
Join Date: Oct 2011
Location: San Diego, CA
Posts: 400
Total Cats: 23
RevMS2v3 engine running erratically. Was perfect 2 days ago. AFR/RPMS/MAF all over!
Sorry for the long title, but was trying to be descriptive. Two days ago my car was running amazingly and it's just been in the garage till today. This afternoon I jumped in it and right as the RPMs started to settle like they always do, the engine stumbled real quick and then just quit like someone shut it off.
I tried starting it a few times while I was checking things over in TS. Sometimes the car will start normally, then, stumble and shut off. And other times I'll start it and the RPMs swing wildly. AFRs are all over the place and it's basically not operable.
I pulled the battery for a couple minutes to see if that would clear the problem and it seemed to, but I took the car for a short drive around the block to check it and after running fine for a few minutes, it cut out. I had to turn if off for a min and restart a few times to barely make it back to my place.
This log is after having the ignition off for a few minutes, start, run, not touch the throttle and let it run it's course. Started a second time and let it run it's course.
After looking over the log, I noticed the MAP looked weird. Moving around a lot and 80kpa engine off, all kinds of crazy. Thoughts anyone please?
TLDR: My MS is going crazy and I need help. Log/Tune included.
MS2v3 reverant built. 2004 MSM regular install. Nothing crazy
Thanks for your help.
I tried starting it a few times while I was checking things over in TS. Sometimes the car will start normally, then, stumble and shut off. And other times I'll start it and the RPMs swing wildly. AFRs are all over the place and it's basically not operable.
I pulled the battery for a couple minutes to see if that would clear the problem and it seemed to, but I took the car for a short drive around the block to check it and after running fine for a few minutes, it cut out. I had to turn if off for a min and restart a few times to barely make it back to my place.
This log is after having the ignition off for a few minutes, start, run, not touch the throttle and let it run it's course. Started a second time and let it run it's course.
After looking over the log, I noticed the MAP looked weird. Moving around a lot and 80kpa engine off, all kinds of crazy. Thoughts anyone please?
TLDR: My MS is going crazy and I need help. Log/Tune included.
MS2v3 reverant built. 2004 MSM regular install. Nothing crazy
Thanks for your help.
#3
Junior Member
Thread Starter
iTrader: (5)
Join Date: Oct 2011
Location: San Diego, CA
Posts: 400
Total Cats: 23
Agreed. I replaced my 2.5 bar map sensor with a 3 bar sensor from Symtech Labs. I'm pretty sure I did a good job soldering it in there and it's been working great for the last few months. Maybe it came loose or went bad.
#4
Junior Member
Thread Starter
iTrader: (5)
Join Date: Oct 2011
Location: San Diego, CA
Posts: 400
Total Cats: 23
FIXED!
Removed MAP signal line and there was coolant in there from when the engine popped last month.
Everything was meticulously cleaned except the vacuum lines. Tomorrow I'm going to take a good look at all of them and do some more cleaning.
Removed MAP signal line and there was coolant in there from when the engine popped last month.
Everything was meticulously cleaned except the vacuum lines. Tomorrow I'm going to take a good look at all of them and do some more cleaning.
Thread
Thread Starter
Forum
Replies
Last Post
eddy1128
Miata parts for sale/trade
8
12-10-2015 05:34 PM
Motorsport-Electronics
ECUs and Tuning
0
09-05-2015 08:02 AM