MEGAsquirt A place to collectively sort out this megasquirt gizmo
Sponsored by:
Sponsored by:

CAN wideband directly to MS3 Basic ?

 
Old 04-12-2019, 03:18 AM
  #1  
Senior Member
Thread Starter
 
Join Date: Nov 2012
Location: Israel
Posts: 640
Total Cats: -422
Default CAN wideband directly to MS3 Basic ?

Can I do that ?
elior77 is offline  
Reply
Leave a poscat -1 Leave a negcat
Old 04-12-2019, 06:05 AM
  #2  
Design Engineer
iTrader: (1)
 
DNMakinson's Avatar
 
Join Date: Jan 2013
Location: Seneca, SC
Posts: 3,510
Total Cats: 468
Default

My understanding is that it can be done with AEM wideband and 1.5.1 FW.


Easy Search

Last edited by DNMakinson; 04-12-2019 at 06:20 AM.
DNMakinson is offline  
Old 04-12-2019, 07:13 AM
  #3  
Elite Member
iTrader: (1)
 
Chiburbian's Avatar
 
Join Date: Feb 2008
Location: Winder, GA
Posts: 2,315
Total Cats: 180
Default

I have the Perfectuning CAN gauge with wideband. It's hooked directly to the MS.

I can't comment on the quality of the sensor etc, but it has been as good or better than my AEM UEGO so far.
Chiburbian is offline  
Old 04-12-2019, 10:26 AM
  #4  
Junior Member
 
rrjwilson's Avatar
 
Join Date: Aug 2008
Posts: 374
Total Cats: 0
Default

There are a few threads about attaching CAN wideband to the MS3 Basic.
Most use the MS CAN module though to interpret the serial output from sensors directly than talk to the MS3.
rrjwilson is offline  
Old 04-13-2019, 10:07 AM
  #5  
Senior Member
Thread Starter
 
Join Date: Nov 2012
Location: Israel
Posts: 640
Total Cats: -422
Default

So in order to connect the AEM via CAN directly to the MS3 Basic I need fw 1.5+ right ?

What are the basic settings I need to put in TS ? What is the AEM remote CAN ID ?

Thanks !
elior77 is offline  
Old 04-13-2019, 11:05 AM
  #6  
Senior Member
 
Join Date: Apr 2017
Location: Greeley, CO
Posts: 602
Total Cats: 60
Default

Originally Posted by DNMakinson View Post
He was kind enough to give you a link. Read the damn thing.
SpartanSV is offline  
Old 04-13-2019, 11:10 AM
  #7  
Senior Member
Thread Starter
 
Join Date: Nov 2012
Location: Israel
Posts: 640
Total Cats: -422
Default

I have read it a few times before posting, it does not say what is the remote id for the AEM when connected directly to the MS or id there any any other special settings beside disabling CAN broadcasting.
elior77 is offline  
Old 04-13-2019, 12:06 PM
  #8  
Senior Member
 
Join Date: Apr 2017
Location: Greeley, CO
Posts: 602
Total Cats: 60
Default

These were the key settings from what I remember. AFAIK this ONLY works with 1.5.1+ firmware and ONLY with the aem X-series 30-0300.


SpartanSV is offline  
Old 04-13-2019, 12:18 PM
  #9  
Senior Member
Thread Starter
 
Join Date: Nov 2012
Location: Israel
Posts: 640
Total Cats: -422
Default

Thanks ! In fact I just got it working before reading your answer.

The fw upgrade via TS was smooth as butter, after disabling "29bit...." and removing the CAN wideband module from the project properties It just worked and it is spot on.

MS3 Basic CAN wideband module for sale
elior77 is offline  
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
90LowNSlo
Build Threads
16
Yesterday 11:42 PM
Joe Perez
Engine Performance
48
03-31-2019 10:09 PM
Morello
MEGAsquirt
1
03-06-2019 08:57 AM
Timothy Tran
MEGAsquirt
20
03-05-2019 09:21 PM
Ncorlis
MEGAsquirt
0
03-04-2019 01:40 PM


Thread Tools
Search this Thread
Quick Reply: CAN wideband directly to MS3 Basic ?


Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.