car starts! unusually high req_fuel, VE tables, no cooling fan :( - Page 2 - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


MEGAsquirt A place to collectively sort out this megasquirt gizmo

Reply
 
 
 
LinkBack Thread Tools
Old 07-27-2011, 03:17 AM   #21
Junior Member
Thread Starter
iTrader: (20)
 
Join Date: Apr 2010
Location: Redmond, WA
Posts: 494
Total Cats: 15
Default

ok, so I got it all soldered up. haven't had time to put it back in the car and do TS settings, but I just choose for PA0 for boost control right? for fan control, is it also in the output settings?
bmxfuel007 is offline   Reply With Quote
Old 07-27-2011, 08:35 AM   #22
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,899
Total Cats: 1,792
Default

correct.
Braineack is offline   Reply With Quote
Old 07-29-2011, 07:02 PM   #23
Junior Member
Thread Starter
iTrader: (20)
 
Join Date: Apr 2010
Location: Redmond, WA
Posts: 494
Total Cats: 15
Default

nevermind. answered my own question. ALED can drive a 12v relay, so ALED directly to 1L is fine. just gotta watch my fans to see if they truly turn on through ALED

Last edited by bmxfuel007; 07-30-2011 at 03:08 PM.
bmxfuel007 is offline   Reply With Quote
Old 08-06-2011, 11:34 PM   #24
Junior Member
Thread Starter
iTrader: (20)
 
Join Date: Apr 2010
Location: Redmond, WA
Posts: 494
Total Cats: 15
Default

is there a test mode to get my radiator fan to come on in megasquirt/TS? been driving the car running autotune, and while sitting at a light, I saw my temps rise up to 213 which scared the crap outta me, luckily the light turned green and I was able to get some air moving through. I know I had the fan working before, so the fan should be fine. I have ALED hooked up for the fan on megasquirt, however in TS, I have PM4 (accel LED) set for coolant with the settings that Brain told me to put. Worked before, now I'm pretty sure my fan isn't working again. Anyway for me to test this output?

looks like I had to have soldered the ALED pullup pin.... what should I have soldered? is there another ALED?

Last edited by bmxfuel007; 08-07-2011 at 01:43 AM.
bmxfuel007 is offline   Reply With Quote
Old 08-07-2011, 03:00 AM   #25
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Please post a picture showing how you modded your board for cooling fan.
Ben is offline   Reply With Quote
Old 08-07-2011, 03:30 AM   #26
Junior Member
Thread Starter
iTrader: (20)
 
Join Date: Apr 2010
Location: Redmond, WA
Posts: 494
Total Cats: 15
Default

my only camera on my phone is on the fritz right now. I have it wired under Pullups 12v, and it says ALED, right under WLED. I didn't see the one next to IG1, IG2, WLD, and ALD before. I'm guessing it should be at ALD? Next to the left of the word BOOT
bmxfuel007 is offline   Reply With Quote
Old 08-07-2011, 09:59 AM   #27
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Sounds to me like you wired it to 12V and not to ALD. You'll need to fix that.
Ben is offline   Reply With Quote
Old 08-07-2011, 01:16 PM   #28
Junior Member
Thread Starter
iTrader: (20)
 
Join Date: Apr 2010
Location: Redmond, WA
Posts: 494
Total Cats: 15
Default

Yeah, initially I thought "oh, since the manuals say ALED can be wired directly to 1L since it supplies a 12v, I can just wire up this hole that says ALED and has a 12v above the section" lol.

Got the ALD wired up and am going to take her for a spin later today. Thanks Ben!
bmxfuel007 is offline   Reply With Quote
Old 08-07-2011, 01:52 PM   #29
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

You're welcome.

The output goes low when activated (aka it's a switched ground).
Ben is offline   Reply With Quote
Old 08-07-2011, 09:28 PM   #30
Junior Member
Thread Starter
iTrader: (20)
 
Join Date: Apr 2010
Location: Redmond, WA
Posts: 494
Total Cats: 15
Default

success fans are working now, thanks a bunch
bmxfuel007 is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
TTE Build - Help me pick tires chrisn Race Prep 27 10-16-2015 06:12 PM
MS PNP requires reading and following directions??? satisfied MEGAsquirt 141 10-06-2015 11:44 AM
Help multi issues here! ReallyRottenTurbo MEGAsquirt 4 09-22-2015 01:49 PM
VE values too low? compuw22c MEGAsquirt 4 09-12-2015 08:42 PM
ME221 Now has Autotune and Long Term Fuel Trim Tables Motorsport-Electronics ECUs and Tuning 0 09-05-2015 09:02 AM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 04:27 AM.